Operating Instructions - Ritter icaro5 Mode D'emploi

Unfold the illustrations at the front
and back of this manual.
Please read these instructions
thoroughly before you start to use
the appliance. Keep these operat­
ing instructions in a safe place
and ensure that they are included
with the appliance if passing it on
to a third party.
Alternatively, the current operat­
ing instructions are available at
www.ritterwerk.de.
INTENDED USE
The food slicer is used for slicing
household foods.
The food slicer is suitable
for contact with
foodstuffs.
If the appliance is used for any
purpose other than its intended
use, or if it is operated incorrectly,
severe injuries may occur or the
appliance may be damaged. All
warranty and liability claims will
be rendered null and void in this
case.
BEFORE USING THE
APPLIANCE FOR THE
FIRST TIME
Preparation
Remove the appliance carefully
from the packaging. Remove all
packaging components and keep
them in a safe place along with
the packaging itself. Clean the
appliance before allowing it to
come into contact with any food
(see CLEANING).
Setting up the appliance
• Set the appliance down on a
flat, non­skid surface close to a
mains socket.
Remove the left­over
holder (12) and then the finger
protection (11) from the appliance
and lift out the tray (5).
Unwind the power cord (14)
to the length required from the
cable compartment (7) under
the appliance. In doing so,
fasten the power cord in the slot
provided for it on the base of the
appliance.
Swivel the slice carriage (10)
into the working position.
Using a small amount of force,
push the finger protection into the
openings on the slice carriage,
and slide it in the direction of the
stop plate (2) until you hear it lock
into place.
Slot the left­over holder
into place on top of the finger
protection.
• Plug the cable into the socket.
USE
Preparation
• Position the tray (5) on the
right of the appliance.
Use the slice thickness adjust­
ment knob (3) to set the required
thickness.
Info:
The slice thickness adjustment
scale (4) is not a millimetre
scale. For safety reasons, the
"0" position is designed to cover
the blade.
Small to regular-sized foods to
be sliced
G
If necessary, unlock the slice
carriage (10) so that it can be
moved. To do so, slide the car­
riage locking device (9) to the left.
• Pull the slice carriage far
enough out of the appliance to
allow you sufficient room to place
the food to be sliced in front of
the rotary blade (16).
H
Place the food to be sliced
onto the slice carriage. Press
it up against the stop plate (2)
using the left­over holder (12).
• Use the left­over holder to
protect your hands. Exception:
Excessively large foods to be
sliced.
Excessively large foods to be
sliced
Info:
Only follow the steps below if you
want to slice an excessively large
piece of food!
• Slide the slice carriage (10)
into the appliance until it locks
into place.
G
Secure the slice carriage in
place by sliding the carriage lock­
ing device (9) to the right.
• Remove the left­over
holder (12).
I
Removing the finger
protection (11):
• Slide the finger protection to
the right until it locks into place.
• Using a small amount of force,
pull the finger protection vertically
upwards and out of the openings
on the slice carriage.
K
Place the food to be sliced
onto the slice carriage.
Slicing
L
icaro / elexa
7 7
Switch the appliance on:
• Press and hold down the
safety lockout button (1a) with
your index or middle finger.
• Press the power button (1b)
with your thumb.
Two operating modes are
available:
• Intermittent operation:
Keep both power control buttons
pressed. The rotary blade (16)
will run until you release the
power button.
• Continuous operation: First
release the safety lockout button
and then the power button. The
rotary blade will continue to run
until you press the safety lockout
button again.
English
11