Parameters; General - Niko 350-34001 Manuel Technique

36 Channel 2 External On/Off
37 Channel 2 External dimming steps
38 Channel 2 External dimming level
39 Channel 2 Lux level switch
40 Channel 2 Lock mode
42 Channel 2 Automatic/Manual
43 Channel 2 Alarm
50 Channel 3 On/Off
51 Channel 3 Dimming steps
52 Channel 3 Dimming level
53 Channel 3 Secondary input
54 Channel 3 Lux level
55 Channel 3 Switch-off delay time
56 Channel 3 External On/Off
57 Channel 3 External dimming steps
58 Channel 3 External dimming level
59 Channel 3 Lux level switch
60 Channel 3 Lock mode
62 Channel 3 Automatic/Manual
63 Channel 3 Alarm
70 HVAC On/Off
73 HVAC Secondary input
75 HVAC Switch-off delay time
76 HVAC External On/Off
80 HVAC Lock
81 HVAC Switch-on delay time

4. PARAMETERS

To configure the 350-34x0x detectors with the KNX ETS software, you should open the parameter screen of the presence detector. To do this, select the presence detector in the Devices panel of the respective project and
click on the Parameter tab.
Warning: do not unplug the KNX bus connector immediately after the upload with the ETS software has been completed. Wait a few seconds to avoid the detector losing its firmware.
Info: Once the upload is complete, the connector needs to be unplugged. Wait 3 seconds after the upload before unplugging the connector.

4.1. General

Parameter Description
Device function
With this parameter, the detector can be configured as a master or secondary device.
Master
Secondary
Sensitivity adjustment This parameter allows you to adjust the sensitivity of the motion detection.
Default value: High
Maximum
High
Medium
Low
Advanced mode This parameter is used to enable Advanced parameters and consequently unlock hidden options.
Default value: Disable
Disable
Enable
PM350-34x0x_EN
On/Off Receives an on/off telegram from an external device
Dimming steps Receives a dimming steps telegram from an external device
Dimming level Receives a dimming value telegram from an external device
On/Off Sends an on/off telegram to an actor when a specific lux level is reached
On/Off Receives a lock/unlock telegram
On/Off Switches back to Automatic mode after receiving a telegram from an external device
On/Off Sends an on/off telegram to an actor when an alarm sets off
On/Off Sends an on/off telegram to an actor when motion is detected
Dimming steps Sends a dimming steps telegram to an actor
Dimming level Sends a dimming value telegram to an actor
Secondary motion Receives a motion telegram from a secondary detector
Lux level Receives a new setpoint or switching value
Switch-off delay time Receives a new switch-off delay time
On/Off Receives an on/off telegram from an external device
Dimming steps Receives a dimming steps telegram from an external device
Dimming level Receives a dimming value telegram from an external device
On/Off Sends an on/off telegram to an actor when a specific lux level is reached
On/Off Receives a lock/unlock telegram
On/Off Switches back to Automatic mode after receiving a telegram from an external device
On/Off Sends an on/off telegram to an actor when an alarm sets off
On/Off Sends an on/off telegram to an HVAC installation or actor
Secondary motion Receives a motion telegram from a secondary detector
Time Value (sec) Receives a new switch-off delay time
On/Off Receives an on/off telegram from an external device
On/Off Receives a lock/unlock telegram
Time Value (sec) Receives a new switch-on delay time
When the device type is set to Master, all the functions and parameters of the Automatic mode are
applicable. A master device can receive the triggering signal from one or more secondary detectors.
When the device type is set to Secondary, it is solely used to extend the detection area.
The motion detection sensitivity is set at the maximum level.
The motion detection sensitivity is set at a high level.
The motion detection sensitivity is set at a medium level.
The motion detection sensitivity is set at a low level.
Only the basic options are made available.
All options are made available.
350-34001/350-34002/350-340X3/350-340X4/350-34902
3
EN