Manifold Re-Ftting - battioni Pagani WPT Série Notice D'emploi Et D'entretien

Instruction Manual
for WPT, KTS, KPS, KTM, WSM series use and maintenance
KTS VERSION
1) attach the lubrication pump to the cooling pump and fasten it with screws;
2) insert the cooling pump shaft in the connector joint;
3) tighten the screws that fasten the cover to the back flange;
4) connect the lubrication pump delivery tubes, inserting them in the con-
necting piece and pressing then until the quick clamping hooks snap;
5) fit the lateral tank support at the pump body;
6) insert the lubrication pump shaft in the connector joint;
7) put lubricating oil in the tank through the oil fill plug;
The KTS/KTM/KPS pump is equipped with a system that allows the flange to
slide, avoiding breakages due to foreign bodies entry between the rotor and
body. (Except G-GA version)
To benefit of this system it is important to respect the following indications:
Before starting the pump, verify that the rotor has not accidentally lowered.

3.9.3 - MANIFOLD RE-FTTING

WPT SERIES
1) replace the manifold gasket;
2) place the manifold on the pump body aligning the manifold screws
holes with the body threaded holes;
3) tighten the screw located under the reversing gear;
4) tighten the screws of the manifold;
5) insert the rubber ball on its seat;
6) fit the valve cover tightening the screws;
7) put the reversing gear in checking that the flat part of the reversing gear
is positioned at 90° to the power
take-off;
8) put the spring on the reversing gear;
9) apply the manifold cover gasket;
10) place the manifold cover and fasten it with screws;
11) insert the selector;
12) screw the handle pin on the selector;
13) fit the discharge elbow.
KPS SERIES
1) Replace the manifold gasket;
2) Place the manifold on the pump body;
3) Tighten the fastening screws of the manifold;
4) Insert the cone;
5) Assemble the spring on the cone;
6) Assemble the spacer on the cone spring;
7) Replace the O-ring on the manifold cover;
8) Place the manifold cover on the manifold;
9) Tighten the fastening screws of the manifold cover;
10) Assemble the oil retainer into the manifold cover housing:
11) Assemble the handle and tighten it with the appropriate screw;
12) Assemble the filter cartridge;
13) Replace the O-ring on the filter cover;
14) Place the filter cover on the manifold;
15) Tighten the fastening screws of the filter cover;
To re-install proceed as for the first installation.
pag. 52
KTM VERSION
1) attach the lubrication pump to the back cover and fasten it with two
screws;
2) insert the lubrication pump shaft in the connector joint;
3) tighten the screws that fasten the cover to the back flange;
4) connect the lubrication pump delivery tubes, inserting them in the pipe
fittings;
5) mount the back tank and tighten the screws that fasten the tank to the
flange;
6) put lubricating oil in the tank through the oil fill plug;
KTS SERIES
1) replace the manifold gasket;
2) place the manifold on the pump body;
3) tighten the manifold fastening screws;
4) insert the rubber ball on its seat;
5) fit the valve cover tightening the screws;
6) put the reversing gear in checking that the flat part of the reversing gear
is positioned at 90° to the power take-off;
7) put the spring on the reversing gear;
8) apply the manifold cover gasket;
9) place the manifold cover and fasten it with screws;
10) insert the selector;
11) screw the handle pin on the selector;
12) fit the discharge elbow.
KTM / WSM SERIES
1) fit the oil check lights;
2) fit the lubrication copper tubes;
3) fit the connectors;
4) fit the cooling pump complete kit (if present);
Slotting Flange