Technical Data; Ambient Conditions; Detection Range/Measuring Range; Electrical Data - Balluff BTL BNC 00 B15A 010-000S92 Série Notice D'utilisation

BTL BNC_ 00- _ _ _ _ -B15A _010-000S92 / BTL ZNC_ 00- _ _ _ _ -B15A _010-000S92
Magnetostrictive Linear Position Sensor – Rod Style
8

Technical data

The specifications are typical values for
BTL BNC_ 00- _ _ _ _ -B15A _010-000S92 and
BTL ZNC_ 00- _ _ _ _ -B15A _010-000S92 at 24 V DC,
room temperature and a measuring length of 500 mm in
conjunction with the BTL-P-1013-4R, BTL-P-1013-4S,
BTL-P-1012-4R or BTL-P-1014-2R magnet.
The product is immediately ready for operation, full
accuracy is achieved after the warm-up phase.
Further data can be found at www.balluff.com
on the product page.
8.1

Ambient conditions

Ambient temperature
Storage temperature
Relative humidity
Operating pressure
Maximum pressure
Typ. temperature coefficient
1)
Shock rating as per
EN 60068-2-27
2), 3)
Continuous shock per
EN 60068-2-27
2), 3)
Vibration per EN 60068-2-6
2), 3)
Protection per IEC 60529 (when
threaded together)
8.2

Detection range/Measuring range

Measuring length
Analog resolution
...-B15AA/-B15A1...
...-B15AE/-B15A5...
Repeat accuracy
with measuring length ≤ 500 mm
with measuring length > 500 mm
Length-dependent measuring
frequency
Measuring length ≤ 1270 mm
Measuring length > 1270 to
≤ 2650 mm
Measuring length > 2650 mm
Non-linearity
with measuring length ≤ 500 mm
with measuring length > 500 mm
Detectable speed
www.balluff.com
8.3
Operating voltage Ub
Current draw (at 24 V DC)
Power consumption
Overvoltage protection
Voltage-proof up to
(GND – Housing)
...-B15AA/B15A1...
−40...+75 °C
...-B15AE/B15A5...
−40...+85 °C
≤ 90%, non-
condensing
8.4
≤ 450 bar
Short circuit protection
750 bar
(10 × 1 min)
Reverse polarity protected
≤ 30 ppm/K
100 g/6 ms
8.5
50 g/2 ms
...-B15AA...
12 g, 10...2000 Hz
...-B15A1...
IP67, IP69K
...-B15AE...
...-B15A5...
25...4000 mm
183 μV
Measuring length 500 mm, magnet in the middle of the measuring range
≥ 4 μm 1)
Individual specifications as per Balluff standard
2)
351 nA
Resonant frequencies excluded
3)
≥ 4 μm
4) A prerequisite is that no current can flow between GND and 0 V in the
event of polarity reversal.
≤ ±10 µm
≤ ±0.002% FS
1000 Hz
500 Hz
250 Hz
±200 μm
±0.04% FS
≤ 10 m/s

Electrical data

...-B15AA/B15A1...
...-B15AE/B15A5...
...-B15AA/B15A1...
...-B15AE/B15A5...
Output current
Load resistance R
Lc

Electrical Connection

4)

Output/Interface

Analog, voltage
Analog, voltage
Analog, current
Analog, current
10...30 V DC
≤ 60 mA
≤ 80 mA
≤ 1.5 W
≤ 2.0 W
Ub up to 36 V DC
500 V DC
≤ 5 mA
≤ 500 ohm
Signal output to GND
and to 30 V DC
Ub up to 30 V DC
0...10 V
10...0 V
4...20 mA
20...4 mA
english 15