Télécharger Imprimer la page

MCS Master DHA 10 Manuel D'utilisation Et De Maintenance page 6

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 21
5. If an extension lead may become overloaded
6. Where the power cable may be damaged
7. On a slope or uneven surface
8. Where there is risk of fire or close to a naked flame
9. Where it may be damaged by chemicals
10. Where there is a risk of interference by foreign objects
11. This product is not made for DIY repair
12. If there is a risk of water falling on the unit
►►
4. PARTS
► FIG. 4
1. Air vent
2. Control panel
► FIG. 5
1. Handle of the unit
2. Air filter
3. Handle of the water tank
4. Drain of the tank
5. Cover of the water tank
6. Water tank
7. Drain hole for continuous drainage
8. Power cord
► FIG. 6
1. Dust filter
2. Active carbon filter
3. Filter fixer
►►
5. PROGRAMMING FEATURE (FIG. 7)
1. MODE BUTTON
By pressing this button, you can set the working mode of
the machine to be:
LOW (MUTE dehumidifying):
When the ambient humidity < set humidity, the unit will run
in LOW fan speed (without Heater).
When the ambient humidity ≥ set humidity, the unit will run
in LOW fan speed & WITH Heater.
HIGH (TURBO dehumidifying):
When the ambient humidity ≥ set humidity, the unit will run
in HIGH fan speed & WITH Heater.
When the ambient humidity < set humidity, machine will
run in HIGH fan speed (without Heater).
DRYER: ALWAYS ON with HIGH fan speed and
HEATER.
2. HUMIDITY BUTTON
Press HUMIDITY button to set the room humidity you
need: continuous dehumidifying , 40%, 50%, 60% or 70%
The relative indicator will light on.
If the humidity button is not set, the unit will work in the
pre-set humidity: 50%..
3. TIMER BUTTON
Press TIMER button to set the working hours you desired.
As you press the button, the LED window will show the
number you chose (starting from 0, 1 to 24 in a cycle).
When the timer is activated, the TIMER Symbol
light on and the setting time would appear 8 seconds on
the LED. After that, LED returns to room humidity again.
When the set time has been reached, the machine will
turn off automatically. If the timer button is not pressed,
the unit will work continuously for 24 hours.
4. POWER (ON/OFF) BUTTON
Press this button to start or turn off the machine. While the
power is on, the power indicator should light on.
5. MUTE OPERATION INDICATOR
While the MUTE function is chosen, this operation
indicator will light on.
6. TURBO OPERATION INDICATOR
While the TURBO function is chosen, this operation
indicator will light on.
7. CLOTHES DRYER OPERATION INDICATOR
While the CLOTHES DRYER function is chosen, this
operation indicator will light on.
8. HUMIDITY DISPLAY WINDOW
Display the room humidity (35~95%RH). While press
"TIMER" button, it shows the setting time, after 8 seconds,
return to room humidity.
9. HUMIDITY SETTING INDICATORS
continuous de-humidifying, 40%, 50%, 60%, 70%.
10. TIMER INDICATOR
Press this button to set the working time (1 to 24 hours).
11. POWER (ON/OFF)/CHECK INDICATOR
When the unit is in normal operation, this indicator will
light in blue. And, in the following conditions, the power
indicator will BLINK to warn you:
► The unit was tipped over.
► The fan is dissipating the heat (after the power is off,
the unit will keep dissipating the heat for 2 minutes to cool
down the unit).
12. WATER FULL INDICATOR
It turns to RED when water tank is full or the tank is not in
proper position.
►►
6. OPERATION
► Plug the unit into a correct mains socket. (Please refer
to the rating label at the rear of the unit.)
► Press button POWER to turn on the unit. The unit will
start to work in continuous mode.
► Press button HUMIDITY to set the room humidity you
need: continuous de-humidifying , 40%, 50%, 60% or 70%
► Press button MODE to choose the ventilation speed,
MUTE, TURBO or DRYER.
► Press button TIMER to set the working hour you need
(1~24 hours).
► To turn off the unit, press button POWER again.
IMPORTANT!
► After switching off the unit, it takes at least 2 minutes
to OFF the unit completely, this allows the heater to cool
would
down. During the cool-down, the power indicator will blink
for warning.
DO NOT DISCONNECT THE PLUG DIRECTLY
FOR QUICK-OFF.
en
IT
DE
ES
FR
NL
PT
DA
FI
NO
SV
PL
RU
CS
HU
SL
TR
HR
LT
LV
ET
RO
SK
BG
UK
BS
EL
ZH

Publicité

loading