Denon DJ X1800 PRIME Guide D'utilisation page 9

3. Link Ports: Use standard networking cables to connect these ports to your SC5000 Prime
units and/or to your computer. Each networked SC5000 Prime can use these connections
share timing and BPM information with X1800 Prime (to synchronize effect tempos) as well
as track and user profile data with other SC5000 Prime units.
4. Master Outputs (balanced XLR): Use standard XLR cables to connect these outputs to
loudspeakers or an amplifier system. Use the Master knob on the top panel to control the
volume level.
5. Master Outputs (unbalanced RCA): Use standard RCA cables to connect these outputs to
loudspeakers or an amplifier system. Use the Master knob on the top panel to control the
volume level.
6. Record Outputs (RCA): Use standard RCA cables to connect these outputs to a recording
interface, external mixer, or other device. Use the Utility menu to select whether or not the
mix sent to these outputs will include the microphones' audio signal (see
Utility Menu >
7. Booth Outputs (1/4"/6.35 mm, TRS): Use standard 1/4"/6.35 mm cables to connect these
outputs to booth monitors or a booth amplifier system. Use the Booth knob on the top
panel to control the volume level. Use the Utility menu to select whether or not the mix
sent to these outputs will include the microphones' audio signal (see
Menu > Microphone).
8. Send Outputs (1/4"/6.35 mm, TRS): Connect these outputs to the inputs of an external
effects module or other device. You can use the Utility menu to set the level of this audio
signal (see Operation > Utility Menu > Advanced
9. Receive Inputs (1/4"/6.35 mm, TRS): Connect these inputs to the outputs of an external
effects module or other device. You can use the Utility menu to set the level of this audio
signal (see Operation > Utility Menu > Advanced
10. Phono/Line Inputs (RCA): Use standard RCA cables to connect these line-level or phono-
level inputs to an external audio source. Use the input selectors on the top panel to set
whether the signal from the line-level inputs or phono-level inputs will be sent to each channel.
11. Grounding Terminal: If you are using phono-level turntables with a grounding wire,
connect the grounding wire to this terminal. If you experience a low "hum" or "buzz", this
could mean that your turntables are not grounded.
Note: Some turntables have a grounding wire built into the RCA connection and, therefore,
nothing needs to be connected to the grounding terminal.
12. Mic 2 Input (1/4"/6.35 mm, TRS): Use a standard 1/4" (6.35 mm) cable (not included) to
connect a standard dynamic microphone to this input. Use the Mic 2 Level knob on the
top panel to control the volume level.
13. MIDI Output (5-pin DIN): Use a standard MIDI cable to connect this output to the MIDI
input of an optional external MIDI device. You can use the MIDI Send button to send MIDI
Start messages from this output. You can also use the Utility menu to enable or disable
this connection (see
14. Digital In (digital RCA): Use digital RCA cables to connect these 24-bit/96 KHz inputs to
the digital outputs of your Denon DJ SC5000 Prime units.
15. Digital Link In (digital RCA): If you are using more than one X1800 Prime unit, use a digital
RCA cable to connect this input to the digital out of another X1800 Prime.
16. Digital Out (digital RCA): Use a digital RCA cable to connect this output to the digital input of
another X1800 Prime unit or an external interface, mixer, or other device. Use the Utility menu
to set the level of the outgoing signal (see
Microphone).
Operation > Utility Menu >
Audio).
Audio).
System).
Operation > Utility Menu > Advanced
Operation >
Operation > Utility
Audio).
9