Publicité
Les langues disponibles
Les langues disponibles
5) Battery tool use and care
a) Recharge only with the charger specified by the
manufacturer.
A charger that is suitable for one type of battery
pack may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically designated
battery packs.
Use of any other battery packs may create a risk
of injury and fire.
c) When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause
irritation or burns.
6) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool
is maintained.
PRECAUTION
Keep children and infirm persons away.
When not in use, tools should be stored out of reach of
children and infirm persons.
PRECAUTIONS FOR CORDLESS DRIVER DRILL
1.
Always charge the battery at a temperature of 0 –
50°C. A temperature of less than 0°C will result in
over charging which is dangerous. The battery cannot
be charged at a temperature higher than 50°C.
The most suitable temperature for charging is that
of 20 – 25°C.
SPECIFICATIONS
POWER TOOL
Model
No-load speed (Low/High)
Wood
(Thickness 18 mm)
Drilling
Metal
(Thickness 1.6 mm)
Capacity
Machine screw
Driving
Wood screw
Rechargeable battery
Weight
CHARGER
Model
Charging voltage
Weight
EBM1430R: Li-ion 14.4 V (3.0 Ah 8 cells)
UC18YRL
7.2 – 18 V
0.6 kg
2.
When one charging is completed, leave the charger for
about 15 minutes before the next charging of battery.
Do not charge more than two batteries
consecutively.
3.
Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
4.
Never disassemble the rechargeable battery and charger.
5.
Never short-circuit the rechargeable battery. Short-
circuiting the battery will cause a great electric
current and overheat. It results in burn or damage
to the battery.
6.
Do not dispose of the battery in fire.
If the battery is burnt, it may explode.
7.
When drilling in wall, floor or ceiling, check for
buried electric power cord, etc.
8.
Bring the battery to the shop from which it was
purchased as soon as the post-charging battery
life becomes too short for practical use. Do not
dispose of the exhausted battery.
9.
Using an exhausted battery will damage the charger.
10. Do not insert object into the air ventilation slots of
the charger.
Inserting metal objects or inflammables into the
charger air ventilation slots will result in electrical
shock hazard or damaged charger.
11. When mounting a bit into the keyless chuck, tighten
the sleeve adequately. If the sleeve is not tight, the
bit may slip or fall out, causing injury.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips
with the protection function to stop the output.
In the cases of 1 and 2 described below, when using this
product, even if you are pulling the switch, the motor
may stop. This is not the trouble but the result of
protection function.
1.
When the battery power remaining runs out (The
battery voltage drops to about 8V), the motor stops.
In such case, charge it up immediately.
2.
If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes
of overloading. After that, you can use it again.
DS14DAL
0–350/0–1200 min
27 mm
Steel: 13 mm,
Aluminum: 13 mm
6 mm
6.8 mm (diameter) × 50 mm (length)
(Requires a pilot hole)
1.6 kg
English
–1
8
Publicité
