EN
•
Risk of tripping over the electric cable. Always be aware
of the whereabouts of the electric cable so that it does not
get in the way of your feet or anything else moving about
in the area.
•
The snow thrower may only be connected with a cable
that is approved for outdoor use.
•
The electric cable with which the snow thrower is
connected must always be intact. It must never be used if
it displays signs of damage.
•
The snow thrower must never be used if its plug, electric
cable or other electrical equipment is damaged.
•
Repairs to the electrical equipment may only be carried
out by an authorised electrician.
•
Never drive over the electric cable for the snow thrower
while working.
•
If the electric cable for the snow thrower has been
damaged while working, the following instructions must
be followed:
A. Stop the motor.
B. Leave the site in the opposite direction from the
damaged point on the cable.
C. Disconnect the cable from the power socket.
•
Stop the motor and disconnect the power supply:
A. If the driver leaves the machine.
B. If the auger housing or discharge chute is blocked and
must be cleaned.
C. Before beginning repairs or adjustments.
•
Always make sure the rotating parts have stopped and all
the controls are disengaged before cleaning, repairing or
inspection.
•
Never drive across a slope. Move from the top down, and
from the bottom to the top. Be careful when changing
direction on a slope. Avoid steep slopes.
•
Never operate the machine with insufficient protection or
without the safety devices in place.
•
Existing safety devices must not be disconnected or
disengaged.
•
Never use the snow thrower near enclosures, cars,
windowpanes, slopes etc. without properly setting the
discharge chute deflector.
•
Always keep children away from areas to be cleared. Get
another adult to keep the children under supervision.
•
Do not overload the machine by driving it too fast.
•
Take care when reversing. Look behind you before and
during reversing to check for any obstacles.
•
Never point the discharge chute towards bystanders. Do
not allow anyone to stand in front of the machine.
•
Only use accessories that are approved by the machine's
manufacturer.
•
Never drive the snow thrower in bad visibility or without
satisfactory lighting.
•
Always ensure you have a good balance and a tight grip
on the handle.
2.4
MAINTENANCE AND STORAGE
•
Tighten all nuts and screws so that the machine is in safe
working condition.
•
Never flush the machine with water. It will make damage
to the electrical equipment and risk of electrical shocks.
•
Check all electrical equipment before use. The snow
thrower must never be used if its insulatings, fittings or
other electrical equipment is damaged.
26
ENGLISH
•
Always use genuine spare parts. Non-genuine spare parts
can entail a risk of injury, even if they fit the machine.
•
Before a long storage, check the instructions for
recommendations.
•
Replace damaged warning and instruction stickers.
•
Let the engine run a couple of minutes with the auger
connected after use. This prevents the auger from
freezing solid.
3.1
UNPACKING
1. Open the box carefully.
2. Take care of any documentation in the box, for example
these instructions.
3. Lift the snow thrower from the box.
4. Cut the tie straps and remove all protecting plastic from
the machine.
5. Dispose of the box and packaging according to local
regulations.
3.2
ASSEMBLY
1. Assemble the snow thrower as follows.
2. See fig. 2. Align the square dog at the shank against the
recess in the handle.
3. Se fig. 3. Slide the shank and the handle together until the
tap locks in the shank.
4. See fig. 4. Screw on, and tighten the big plastic nut.
5. See fig. 5. Assemble the black plastic sleeve on the shank
until the tap locks in the shank hole.
6. See fig. 6. Align the shank against the snow thrower so
the sleeve groove fits against the hole bar.
7. See fig. 7. Slide the shank into the snow thrower and
assemble the two screws with nuts. Tighten with a Philips
screwdriver.
The snow thrower is intended for small snow cleaning works
quite close to houses with stationary 230 VAC electric net.
The snow thrower controls are shown in fig. 1 and described
below.
Pos Denomination
A Starting lockout
B Start lever
C Connecting device For connection of current.
D Cable support
E Lock handle
F Handle
G Shank
H Lock handle
J Auger housing
K Auger
Original instructions for use
3 ASSEMBLY
4 DESCRIPTION
Description
Prevents the start lever to be
activated unintentionally.
Starts the engine. The lever can be
activated if the starting lockout A is
depressed.
For supporting the connection cable.
For securing the shank handle.
The length can be adjusted.
For securing the shank.