Stiga SNOW ELECTRIC 31 Mode D'emploi page 27

5 USING THE MACHINE
5.1 GENERAL
Never start the engine until all the above measures under
'ASSEMBLY' have been carried out.
Never use the snow thrower without first reading
and understanding the enclosed instructions and
all the warning and instruction stickers on the
snow thrower and in these instructions.
Always wear protective goggles or a visor during
use, maintenance and service.
5.2 BEFORE STARTING
The connection cable and its plugs must be fault
free and approved for outdoor use.
The connection cable may only be connected to
power sockets equipped with an earth leakage cir-
cuit breaker with a trip current of max. 30 mA.
The connection cable must be suspended on the ca-
ble support. Otherwise there is a risk of damage
alongside the plug which is potentially life-threat-
ening.
Connect the snow thrower with the electric cable from the
property's power socket.
Suspend the cable on the cable support (1:D) and connect to
the connector (1:C).
5.3 START
Start the motor and the auger as described below.
1. Lean the snow thrower back slightly so that the auger is
raised a little above the ground.
2. Press in and hold the starting lockout (1:A) . Squeeze the
start lever (1:B).
3. Release the starting lockout, lower the auger towards the
ground and start to clear the snow.
5.4 SAFETY TEST
After starting and before use of the machine, it is essential
to perform the safety test below.
If the unit fails to operate as described, DO NOT operate it.
In this case, contact an authorised workshop for repair.
Auger test
Release the start lever. The motor and the auger should stop
immediately.
5.5 STOP
Stop the motor and the auger by releasing the start lever
(1:B).
5.6 SNOW CLEARANCE
Never aim the snow at bystanders.
Always stop the engine before unclogging.
Always wear eye protection when operating the
snow thrower.
If the auger is blocked, never try to keep the motor
engaged for more than 20 seconds. Extensive en-
gagement will damage the motor.
ENGLISH
1. Start the motor as described above and check the ejection
distance and direction.
2. Push the snow thrower slowly forwards and hold it in a
slight angle to throw the snow to the left or to the right.
3. Stop working by releasing the start lever (1:B).
5.7 OPERATING TIPS
1. Clear away the snow immediately after snowfall.
2. For complete snow clearance, slightly overlap each
clearance pass.
3. If possible, discharge the snow downwind.
4. For safety and to prevent damage to the snow thrower,
keep the area to be cleared free of stones, toys and other
foreign objects.
5. The snow thrower's capacity depends on the depth and
density of the snow. Learn how the snow thrower works
in different snow conditions.
5.7.1
Snow up to 15 cm deep can be removed quickly and easily
by clearing at an even speed. Plan for downwind discharge of
the snow.
5.7.2
Chop packed snow using a spade or similar. Then push the
snow thrower slowly forward. Never hoe with the snow
thrower. This will destroy it.
5.8 AFTER USE
The snow thrower must never be rinsed with wa-
ter. Risk of damage to the electrical system and
risk of electric shocks.
1. Stop the motor.
2. Disconnect the electric cable from the snow thrower and
the property's power socket.
3. Clean the inside and outside of the snow thrower with a
suitable brush.
4. Check that there are no damaged or loose parts. Repair/
replace parts if necessary.
The electrical connection must be disconnected
before carrying out maintenance work.
6.1 BEFORE USE
• Every time the snow thrower is to be used, check that the
electrical equipment is intact and free of faults. The snow
thrower must not be used if there are any faults or if
anything is missing.
• Check that the auger rotates easily.
• Check that all screw joints are tightened. Tighten if
necessary.
• Apply silicon spray to the auger. This prevents icing.
• Check that the starting handle cannot be activated
without the ignition lock being moved to the left.
Original instructions for use
Dry and normal snow
Wet, packed snow
6 MAINTENANCE
EN
27