Publicité
Les langues disponibles
Les langues disponibles
GENERAL SAFETY INSTRUCTIONS
Warning! Read and understand
all instructions. Failure to follow all
instructions listed below may result
in electric shock, fire and/or serious
personal injury.
Save these instructions.
WORK AREA
• Keep your work area clean and well
lit. Cluttered benches and dark areas
invite accidents.
• Do not operate power tools in
explosive atmospheres, such as in
the presence of flammable liquids,
gases, or dust. Power tools create
sparks that may ignite the dust or fumes.
• Keep bystanders, children, and
visitors away while operating a
power tool. Distractions can cause you
to lose control.
ELECTRICAL SAFETY
• Double insulated tools are equipped
with a polarized plug (one blade is
wider than the other.) This plug will
fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit,
contact a qualified electrician to install
a polarized outlet. Do not change
the plug in any way. Double Insulated
eliminates the need for the three wire
grounded power cord and grounded
power supply system.
• Avoid body contact with grounded
surfaces such as pipes, radiators,
ranges and refrigerators. There is an
increased risk of electric shock if your
body is grounded.
• Don't expose power tools to rain
or wet conditions. Water entering
a power tool will increase the risk of
electric shock.
GB
4
General Safety Instructions
• Do not abuse the cord. Never use the
cord to carry the tools or pull the plug
from an outlet. Keep cord away from
heat, oil, sharp edges or moving parts.
Replace damaged cords immediately.
Damaged cords increase the risk of
electric shock.
• When operating a power tool
outside, use an outdoor extension
cord marked "W-A" or "W". These
cords are rated for outdoor use and
reduce the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are
doing and use common sense when
operating a power tool. Do not use
tool while tired or under the influence of
drugs, alcohol, or medication. A moment
of inattention while operating power tools
may result in serious personal injury.
• Dress properly. Do not wear loose
clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,
jewelry, or long hair can be caught in
moving parts.
• Avoid accidental starting.
Be sure switch is off before plugging in.
Carrying tools with your finger on the
switch or plugging in tools that have the
switch on invites accidents.
• Remove adjusting keys or
wrenches before turning the tool
on. A wrench or a key that is left
attached to a rotating part of the tool
may result in personal injury.
• Do not overreach. Keep proper footing
and balance at all times. Proper footing
and balance enables better control of the
tool in unexpected situations.
• Use safety equipment. Always
wear eye protection. Dust mask, non-
skid safety shoes, hard hat, or hearing
protection must be used for appropriate
conditions.
TOOL USE AND CARE
• Use clamps or other practical
way to secure and support the
workpiece to a stable platform.
Holding the work by hand or against
your body is unstable and may lead to
loss of control.
• Do not force tool. Use the correct
tool for your application. The correct
tool will do the job better and safer at
the rate for which it is designed.
• Do not use tool if switch does not
turn it on or off. Any tool that cannot be
controlled with the switch is dangerous and
must be repaired.
• Disconnect the plug from the
power source before making any
adjustments, changing accessories,
or storing the tool. Such preventive
safety measures reduce the risk of
starting the tool accidentally.
• Store idle tools out of reach of
children and other untrained
persons. Tools are dangerous in the
hands of untrained users.
• Maintain tools with care. Keep
cutting tools sharp and clean.
Properly maintained tools, with sharp
cutting edges are less likely to bind and
are easier to control.
• Check for misalignment or binding
of moving parts, breakage of parts,
and any other condition that
may affect the tool's operation. If
damaged, have the tool serviced
before using. Many accidents are caused
by poorly maintained tools.
• Use only accessories that are
recommended by the manufacturer
for your model. Accessories that may
be suitable for one tool may become
hazardous when used on another tool.
SERVICE
• Tool service must be performed
only by qualified repair personnel.
Service or maintenance performed by
unqualified personnel could result in a
risk of injury.
• When servicing a tool, use only
identical replacement parts. Follow
instructions in the Maintenance
section of this manual. Use of
unauthorized parts or failure to follow
Maintenance Instructions may create a
risk of electric shock or injury.
ADDITIONAL SAFETY RULES
FOR DOWELLING MACHINES
Remove the plug from the socket before
carrying out any adjustment, servicing or
maintenance.
• Fully unwind cable drum extensions to
avoid potential overheating.
• When an extension cable is required,
you must ensure it has the right ampere
rating for your power tool and is in a safe
electrical condition.
• Ensure your mains supply voltage is the
same as your tool rating plate voltage.
• Your tool is double insulated for additional
protection against a possible electrical
insulation failure within the tool.
• Always check walls, floors and ceilings to
avoid hidden power cables and pipes.
• After long working periods external
metal parts and accessories could be hot.
• Do not force the tool. Let it work at
a reasonable speed. Overloading will
occur if too much pressure is applied
and the motor slows resulting in
inefficient operation and possible damage
to the motor.
• Never start the machine with the drill bit
touching the work piece.
• Never set down the tool until the motor
has come to a complete standstill.
• Keep hands well away from the cutting
area. Do not reach under the work piece
during operation. Do not move or remove
the work piece while operating this tool.
• Use only good quality drill bits that are
suitable for the tool.
• Do not use drill bits that are damaged
or misshapen.
General Safety Instructions
5
GB
Publicité
