Publicité
Les langues disponibles
Les langues disponibles
M o d e l l s p o r t
Congratulations on your purchase of the new RAT.
The RAT is a high-quality FRP pylon speed model, which we have developed for experienced and
ambitious model aircraft pilots.The construction of such a model and related detailed solutions are
subject to a certain taste dependency. Therefore, the solutions of this manual are to be understood
as a suggestion. The PNP version (Plug and Play) is already very much prefabricated. The ARF version
(Almost Ready to Fly) requires model-building experience and basic technical skills in construction.
In any case, there are different ways and approaches to get a very good flying model. Some alter-
natives are therefore discussed during the construction description, but not shown in the picture.
PLEASE READ THE INSTRUCTION VERY CAREFULLY COMPLETE BEFORE STARTING!
F L I G H T I N S T R U C T I O N S
• Before the first flight, observe the instructions in the „Safety Instructions" section.
• When flying the model, you should choose a day with as little wind as possible
• A large, flat area without obstacles (trees, fences power lines etc.) is suitable for the first flights.
• Please carry out a functional test of the drive train / power set and remote control.
• After assembling the model on the airfield, check once again that all model components such as
wing, tail units, wing mounts, engine, linkages, etc. are firmly and properly fastened.
• For a hand start a helper should be present, who can throw the model with enough thrust into the
air.
• The start usually takes place against the wind.
• Do not stall the model near the ground
• Do not initiate tight turns in the immediate vicinity of the ground.
• Check the reactions of the model to the rudder deflections. If necessary, adjust after landing to
increase or decrease the deflections accordingly.
• The minimum flight speed must be at an adequate safety altitude.
• Initiate the landing with sufficient speed
S A F E T Y I N S T R U C T I O N S F O R R E C H A R G E A B L E B A T T E R I E S
• Do not immerse the battery in water or other liquids.
• Do not heat, throw into fire or microwave.
• Do not short-circuit or charge with reversed polarity
• Do not expose, deform or throw the battery
• Do not solder directly on the battery
• Do not change or open the battery
• Only charge the battery with suitable chargers, never connect it directly to a power supply unit.
• Never charge or discharge the battery or charger on a flammable surface.
• Never leave the battery unattended during charging or discharging processes.
• Never charge or discharge the battery in direct sunlight or near heaters or fire.
• Do not use the battery in places subject to high static discharge.
All this can cause the battery to be damaged, explode or even catch fire!
• Keep the battery away from children
• Keep leaked electrolyte away from fire, as it is highly flammable and may ignite.
• The electrolyte liquid should not get into the eyes, if it does, rinse immediately with plenty of clear
water and then see a doctor.
• The electrolyte liquid can also escape from clothes and other objects with a lot of water or was-
hed off.
• Observe the safety instructions of the battery manufacturer and the charger manufacturer.
I N S T R U C T I O N S A N D U S E R M A N U A L
P R E F A C E
T E C H N I C A L D A T A
Span
1300 mm
Length
730 mm
Weight (dry)
420 g
Flying weight
1050 g
Wing Area
16,8 dm²
Airfoil
MH-43
C.G.
47 - 52 mm
B O X C O N T E N T / N E E D E D A C C E S S O R I E S
ARF
Motor
not included
ESC
not included
Folding Prop
not included
Spinner
not included
Battery
not included
Servo ELE
not included
Servo RUD
/
Servo AILE
not included
Servo FLAP
/
3x 25cm, 2x 15cm (JR) not
Servo cable
included
MULITlock
/
MPX plugs
/
UHU Por, Adhesives, Activator
Adhesives
(not included)
TX
min. 4 Channels (not included) min. 4 Channels (not included)
RX
min. 4 Channels (not included) min. 4 Channels (not included)
Elevator
yes
Rudder
no
Ailerons
yes
Flaps
no
Flaps
no
Motor
yes
Landing Gear
no
PNP
Robbe ro-Power X36-1000 #5805 (built-in)
RoControl 6-60 #8711 (not included)
Rasa CFK 9x7" (included))
Alu Turbo Spinner 38mm (included))
Ro-Power 4S 2200mAh (not included)
1x Robbe FS-166 BB MG #9105 (built-in)
/
2x Robbe FS-166 BB MG #9105 (built-in)
/
2x 15cm (JR)
/
/
UHU Por, Adhesives, Activator (not included)
11
Publicité
