Starting; Equipotential Bonding; Instructions For Use; Accessories - Cooper Hand Tools Weller WS 51 Mode D'emploi

English

3. Starting

Assemble soldering iron
drawing).Place the soldering iron in the safety rest. Insert
the soldering iron plug into the connection bush (6) of
the control unit and lock by turning to the right. Check
that the power supply corresponds to the specifications
on the name plate and that the power switch (1) is in the
OFF position. On version that can be switched, set the
voltage on selection switch (9) (set in the factory to 240
V ). Connect the control unit to the power supply. Set the
temperature at the rotary potentiometer (3). Switch on
unit at the supply switch (1). Green LED (2) will illumina-
te. This LED functions as the optical regulator. Constant
illumination means that the system is overheating. The
blinking light signals that the operating temperature has
been reached.
Setting the temperature
The digital display (2) shows the actual value temperatu-
re. By pressing the UP or DOWN key (3, 4) the digital
display (2) switches to the setpoint. The setpoint can be
changed by tapping or by firmly pressing the UP or
DOWN button (3, 4) in the desired
direction. Pressing the button will change the setpoint
quickly. The digital display (2) returns automatically to
the actual value approximately 2 seconds after releasing
the button.
Maintenance
The transition between the heating element / sensor and
the tip of the soldering iron may not come in contact with
dirt, foreign particles or become damaged, since this
affects the precision of the temperature control.

4. Equipotential bonding

The various circuit elements of the 3,5 mm jack bush (5)
make 4 variations possible:
Hard-grounded: No plug (delivery form)
Equipotential bonding: With plug, equalizer at center
contact (impedance 0 ohms)
Potential free: With plug
Soft-grounded: With plug and soldered resi
stance.
Grounding with set resistance value.

5. Instructions for use

For initial heating, coat the selective tinnable tip with sol-
der. This removes any oxidation or dirt on the tip which
13
may have occurred during storage. During pauses bet-
rest (see exploded ween soldering and before storing the soldering iron,
ensure that the tip of the soldering iron is well coated. Do
not use aggressive fluxing agents.
Note: Always ensure the proper position of the solde-
ring iron tip.
These soldering irons have been adjusted for an average-
size tip. Deviations can occur due to exchanging of the tip
or using other tip designs.

6. Accessories

5 29 161 99 Soldering iron set WSP 80 (WS 81 only)
5 33 131 99 Soldering iron set MPR 80 (WS 81 only)
5 33 111 99 Soldering iron set MLR 21
5 33 112 99 Soldering iron set LR 21, antistatic
5 33 113 99 Soldering iron set LR 82 (WS 81 only)
5 33 133 99 Soldering iron set WTA 50
5 13 050 99 Reflow soldering unit EXIN 5
5 27 028 99 Preheating plate WHP 80 (WS 81 only)
5 33 155 99 Soldering iron set WMP (WS 81 only)
5 25 030 99 Thermal insulating unit WST 20

7. Scope of supply

WS 81
Control unit
Soldering iron WSP 80
Power cable
Operating instructions
Soldering iron rest
Jack
WS 51
Control unit
Soldering iron LR 21
Power cable
Operating instructions
Soldering iron rest
Jack
PU 81 / PU 51
Control unit
Power cable
Operating instructions
Jack
Illustration: Circuit diagram, see Page 49 + 50
Illustration: Exploded view, see Page 51 + 52
Subject to technical alterations and amendments!