Table des Matières
Publicité
ASSEMblY
•
Stand the vacuum cleaner up straight and slide the hose into guides at the back of the
vacuum cleaner and click into place.
•
Ensure the hose is straight and slide the wand straight down into the hose until it clicks into
place.
•
Click the wand handle into the top of the vacuum cleaner.
•
Attach the tools to the vacuum cleaner and wind the cord counter-clockwise around cord
hooks and secure with clip.
USINg YOUR dYSON vACUUM ClEANER
Unwind the cord and insert the plug into a suitable socket.
Hold the cleaner head down with your foot and pull the handle downwards.
To switch 'ON' or 'OFF' press the power button in front of the handle.
CAUTION:
•
Do not allow the vacuum cleaner to be used by anyone who may not be able to operate it
safely.
•
The use of an extension cord is not recommended.
•
Always switch off and unplug before performing maintenance on your vacuum cleaner.
•
When returning to the upright position, ensure that the wand and clear bin
fully upright before releasing the vacuum cleaner.
•
Ensure the cyclone is secured to the vacuum cleaner. Do not press the cyclone release
button or shake the vacuum cleaner while carrying or it could fall and cause injury.
•
Store the vacuum cleaner indoors. Put the vacuum cleaner away after use with the cord
coiled safely, to prevent tripping hazards.
•
Do not use outdoors or on wet surfaces or to vacuum water or other liquids – electric shock
could occur.
•
Do not lubricate any parts, or carry out any maintenance or repair work other than that
shown in this Operating Manual, or advised by the Dyson Helpline.
PLEASE NOTE:
•
This vacuum cleaner is intended for household use only.
•
Fine dust such as plaster dust or flour should only be vacuumed in very small amounts.
•
Do not use the vacuum cleaner to pick up sharp hard objects, small toys, pins, paper clips,
etc. They may damage the vacuum cleaner.
•
The vacuum cleaner may be used inside a garage only when used with the Model 08909
Dyson Car Cleaning Kit accessories.
•
If used in a garage, care should be taken to wipe the soleplate and wheels with a dry cloth
after vacuuming to clean off any sand, dirt, or pebbles that could damage delicate floors.
•
Consult your flooring manufacturer's recommended instructions before vacuuming and
caring for your flooring, rugs, and carpet. Some carpets will fuzz if a rotating brush bar
is used when vacuuming. If this happens, we recommend vacuuming in bare floors mode
and consulting with your flooring manufacturer.
•
When vacuuming, certain carpets may generate small static charges in the clear bin
These are entirely harmless and are not associated with the mains supply. To minimise any
effect from this, do not put your hand or insert any object into the clear bin™ unless you
have first emptied it and rinsed it out with cold water (see 'Clear bin
CARPETS/hARd FlOORS
The brush bar will always default to 'ON' (spinning) each time you switch on the vacuum
cleaner and recline it for cleaning. The brush bar will automatically stop if it becomes
obstructed. If the brush bar stops during use, please refer to the 'Clearing brush bar
obstructions' section.
To switch the brush bar 'OFF' (e.g. for hard floors), recline the vacuum and turn it 'ON',
then press the brush bar 'ON/OFF' button – the brush bar will stop spinning.
hIgh-REACh ClEANINg
CAUTION:
•
Switch 'OFF' the vacuum cleaner before changing tools.
•
Powerful suction can cause the hose to 'pull back' – please take care.
•
Take extra care when vacuuming on stairs; do not work with the vacuum cleaner above you
on the stairs. Do not put the vacuum cleaner on chairs, tables etc.
•
Ensure the vacuum cleaner is in upright position before using tools.
PLEASE NOTE:
•
To release the wand, open the wand cap and pull the red tube until the wand releases from
the vacuum cleaner. Tools can be attached to either the hose or wand.
•
The brush bar will not rotate when the vacuum cleaner is in an upright position.
•
Ensure wand cap is closed when not in use.
ClEAR bIN
EMPTYINg
TM
CAUTION:
•
Switch 'OFF' the vacuum cleaner and unplug before emptying the clear bin
PLEASE NOTE:
•
Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
•
To remove the clear bin
from the vacuum cleaner, press the red button at the rear of
TM
cyclone carrying handle.
To release the dirt, press the red bin release button.
•
Do not use the vacuum cleaner without the clear bin
•
Emptying into a bag is recommended for allergy sufferers.
ClEAR bIN
ClEANINg
TM
CAUTION:
•
Do not immerse the whole cyclone in water or pour water into the cyclones.
•
Ensure the clear bin
is completely dry before replacing.
TM
PLEASE NOTE:
•
Do not use detergents, polishes or air fresheners to clean the clear bin
•
Do not put clear bin
in a dishwasher.
TM
WAShINg YOUR FIlTERS
DO ThIS EVERy 3 MONThS
CAUTION:
•
Switch 'OFF' and unplug the vacuum before removing the filters.
•
Ensure filters are completely dry before refitting to the vacuum cleaner.
PLEASE NOTE:
•
This vacuum cleaner has two filters, located as shown. It is important to check your
filters regularly and wash at least every 3 months according to instructions, to maintain
performance.
•
After washing please leave for 24 hours to dry completely.
•
It is normal for filters to turn grey in color. The filters may require more frequent washing if
vacuuming fine dust.
•
Do not use detergents to clean the filters.
•
Do not put the filters in a dishwasher, washing machine, tumble dryer, oven, microwave or
near an open flame.
8
DC27_ALF_CA_OPS-MAN.indd 8
assembly are
TM
.
TM
cleaning' section).
TM
.
TM
in place.
TM
.
TM
lOOKINg FOR blOCKAgES
CAUTION:
•
Switch 'OFF' and unplug the vacuum cleaner before checking for blockages. Failure to do
so could result in personal injury.
•
Please ensure the vacuum cleaner is upright and switched off before removing hose or
airway inspection parts.
•
Beware of sharp objects when clearing blockages.
•
Refit all parts of the vacuum cleaner securely before using.
PLEASE NOTE:
•
Clearing blockages is not covered by your vacuum cleaner's limited warranty.
•
This vacuum cleaner is fitted with a thermal cut-out. If any part of the vacuum cleaner
becomes blocked, it may overheat and automatically cut-out. Switch 'OFF' and unplug the
vacuum cleaner and leave to cool down before checking filters or for blockages.
ClEARINg bRUSh bAR ObSTRUCTIONS
CAUTION:
•
Switch 'OFF' and unplug the vacuum cleaner before clearing brush bar obstructions.
Failure to do so could result in personal injury.
•
Beware of sharp objects when clearing obstructions.
•
Refit all parts of the vacuum cleaner securely before using.
PLEASE NOTE:
•
Clearing brush bar obstructions is not covered by your vacuum cleaner's limited warranty.
7/10/08 11:22:07
Publicité
Table des Matières
