Bench Mounting; Service And Maintenance; Accessories; Environment - Festool EHL 65 EQ Notice D'utilisation D'origine

A support foot [1-10] is fitted to the end of the plan-
er foot so that the EHL 65 EQ can be set down safe-
ly.When the machine is lifted up, the support foot
automatically swivels over the edge of the planer
foot so that the blade does not touch the surface
when the planer is set down.
8.2 Chamfering
The front planer foot is fitted with a 90° V groove [1-
11] for chamfering workpiece edges. The V groove
is 2 mm deep so that 2 mm of the edge is chamfered
when the planing thickness is set to 0.
8.3

Bench mounting

The planer can be operated as a stationary machine
in combination with bench unit SE-EHL (488524).
9

Service and maintenance

WARNING
Risk of injury, electric shock
Always disconnect the mains plug from the
socket before performing maintenance work on
the machine!
All maintenance and repair work which requires
the motor housing to be opened must only be
carried out by an authorised service workshop.
Customer service and repair only
through manufacturer or service
workshops: Please find the nearest
address at: www.festool.com/service
Only use original Festool spare parts!
EKAT
4
Order No. at: www.festool.com/service
5
3
2
1
The machine is equipped with special carbon
brushes. If they are worn out, the power is inter-
rupted automatically and the machine comes to a
standstill.
To ensure constant air circulation, always keep the
cooling air openings in the motor housing clean and
free of any obstruction.
10

Accessories

The order numbers of the accessories and tools can
be found in the Festool catalogue or on the Internet
under "www.festool.com".
10.1 Fitting the rebate depth stop [5]
The rebate depth stop [5-2] can be adjusted in in-
finite variables to a setting between 0 to 23 mm. The
marking [5-1] indicates the rebate depth setting.
10.2 Fitting the parallel stop [6]
In order to plane along an edge, the planing width
can be adjusted from 0 to 65 mm by releasing the
clamp [6-1] and adjusting the stop.
11

Environment

Do not dispose of the device in house-
hold waste! Recycle devices, accesso-
ries and packaging. Observe applica-
ble national regulations.
EU only: In accordance with European
Directive on waste electrical and electronic equip-
ment and implementation in national law, used
electric power tools must be collected separately
and handed in for environmentally friendly recy-
cling.
Information on REACh: www.festool.com/reach
12

EU Declaration of Conformity

One-handed planer
EHL 65 EQ
Year of CE mark: 2012
We declare under sole responsibility that this prod-
uct complies with all the relevant requirements in
the following directives, standards and normative
documents:
2006/42/EG, 2004/108/EG (until 19.04.2016), 2014/
30/EU (from 20.04.2016), 2011/65/EU, EN 60745-
1:2009, EN 60745-2-14:2009 + A2:2010, EN 55014-
1:2006+A2:2011, EN 55014-2:1997+Corrigendum
1997+A1:2001+A2:2008,
A1:2009+A2:2009, EN 61000-3-3:2013.
Festool GmbH
Wertstr. 20, D-73240 Wendlingen, Germany
Dr. Johannes Steimel
Head of Research, Development and Technical
Documentation
2015-03-04
EHL 65 EQ GB
Serial no.
10005425, 499543,
10008100, 10008101
EN 61000-3-2:2006+
13