Model Mm40 - Dremel Multi-Max MM20 Traduction De La Notice Originale

Model MM40

Voltage Rating:
Wattage Rating:
No Load Speed:
Oscillation Angle, left/right: 1,5°
Weight:
ExtEnsiOn cOrDs
Use completely unrolled and safe extension cords with a capacity
of 5 Amps.
assEMBlY
alwaYs turn Off tHE tOOl BEfOrE
WARNING
!
cHanging accEssOriEs, cHanging
cOllEts, Or sErVicing tHE tOOl anD rEMOVE BattErY
Pack.
gEnEral
This Dremel Multi-Max Tool is intended for dry sanding of
surfaces, corners, edges, for scraping, for sawing soft metals,
wood and plastic components, and for grout removal using the
applicable tools and accessories recommended by Dremel.
PICTURE 1
A. On/Off switch
B. Variable speed control dial
C. Power cord
D. Ventilation openings
E. Blade washer
F. Accessory holder
G. Accessory
H. Clamping screw
PICTURE 2
A. Quick Lock™ lever
B. On/Off switch
C. Variable speed control dial
D. Power cord
E. Ventilation openings
F. Accessory holder
G. Accessory
H. Clamping flange
installing anD rEMOVing accEssOriEs
NOTE: Be sure to read the instructions supplied with your Dremel
accessory for further information on its use.
Use only Dremel tested, high performance accessories.
Dremel cutting, scraper blades have a Quick-Fit slot which allows
for faster accessory removal compared with other conventional
oscillating tool systems.
220V-240V ~ 50/60Hz
270W
n(o) 10000-21000 min-1
1.46 kg
Model MM20
1. Loosen the clamping screw using the hex key provided
just enough so you can slide the accessory between the
accessory holder and the blade washer (Picture 3).
PICTURE 3
A. Accessory holder
B. Clamping screw
C. Hex key
D. Blade washer
E. Accessory
F. Accessory
G. Washer with bevel up
2. Clean accessory holder, accessory and the clamping screw
with a clean cloth.
3. Place the accessory onto the accessory holder making
sure the accessory engages all pins in the holder and the
accessory is flush against the accessory holder.
4. Securely tighten the clamping screw with the hex provided
(Picture 4).
PICTURE 4
A. Clamping screw
B. Hex key
NOTE: Some accessories, such as scrapers or blades, may be
mounted either straight on the tool, or at an angle to enhance
usability (Picture 5).
PICTURE 5
installing anD rEMOVing accEssOriEs
witH quick lOck™ accEssOrY cHangE
Model MM40
The Dremel Multi-Max MM40 includes an integrated accessory
change mechanism. The Quick Lock™ accessory interface allows
you to install and remove accessories without the need of a
wrench or hex key. You will also no longer need to worry about
losing a clamping screw & washer as these parts are no longer
used in the MM40 version of the Multi-Max.
1. To install an accessory using the Quick Lock™ feature, hold
tool upside down to prevent the blade from falling off the
accessory holder when installing and removing accessories.
2. Turn the Quick Lock™ lever on the top on the tool counter-
clockwise to unlock the clamping mechanism (Picture 6).
The lever needs to be fully engaged to unlock the clamping
mechanism.
PICTURE 6
A. Open
B. Close
3. Clean accessory holder, accessory and the clamping flange
with a clean cloth.
4. Place the accessory onto the accessory holder making
sure the accessory engages all pins in the holder and the
accessory is flush against the accessory holder (Picture 7 &
Picture 8).
10