Home Position Adjust - Briteq BT-575W Mode D'emploi

ENGLISH
Led Display
Display on: display is always on.
Display off: display is off when not used.
 Press the MENU button until the display shows
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select
(display always on) or
 Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Display Inversion
Display normal: display is readable when the unit is on the floor.
Display inversion: display is readable when the unit is mounted upside down.
 Press the MENU button until
is blinking on the display. (normal display)
 Use the ENTER button to change to the mode
stored after 8 seconds. Or press the ENTER button again return to the mode
To go back to the functions press the MENU button.
Focus Adjust
Used to help you adjusting the focus of the light beam .
 Press the MENU button until the display shows
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select a value between 0 and 255.
 Once the value has been selected, press the ENTER button to setup
(or automatically return to the main functions without any change after 8 seconds. )
To go back to the functions without any change press the MENU button again.
Self-Test
Used to activate the internal "self-test" program which shows all possibilities of the unit.
 Press the MENU button until
is blinking on the display.
 Press the ENTER button to start the internal self-test program.
 To go back to the functions press the MENU button.
Ambient temperature of lamp
Used to show the temperature inside the lamp compartment
 Press the MENU button until the
sign is blinking on the display.
 Press the ENTER button and the ambient temperature of lamp will show on the display.
 To go back to the functions press the MENU button again.
Fixture Hours
Used to show the number of working hours of the unit.
 Press the MENU button until
is blinking on the display.
 Press the ENTER button to show the number of working hours in the display.
 To go back to the functions press the MENU button.
BRITEQ
®
OPERATION MANUAL
.
(display off when not used).
(display inversion), the option will be automatically
(normal display).
.
7/68 BT-575W
ENGLISH
Lamp Display
Used to switch the lamp ON/OFF so you can cool the lamp with the internal fans before
transportation
 Press the MENU button until
is blinking on the display.
 Press ENTER button so the display starts blinking.
 Use DOWN and UP button to select the
 Once the mode is selected, press the ENTER button to setup
(or automatically return to the main functions without any change after 8 seconds)
 To go back to the functions without any change press the MENU button again.
Lamp Mode
 Press the MENU button until the
is showing on the display.
 Press ENTER button so the display starts blinking.
 Use DOWN and UP button to select the
Once the mode has been selected, press the ENTER button to setup
(or automatically return to the main functions without any change after 8 seconds.)
To go back to the functions without any change press the MENU button again.
Reset
Used to force a reset of the unit.
 Press the MENU button until
is blinking on the display.
 Press the ENTER to reset all channels to their standard position.
 To go back to the functions press the MENU button.
Please also check the chapter about the DMX-channel configuration of the unit to find out how you can force
a reset by DMX.

HOME POSITION ADJUST


Press MENU button for at least 5
seconds to go into offset mode

Now you can adjust the home position
( this is the zero position )

When you want to adjust gobo and
color home position, you should run
mode first

The functions are shown below:
Pan offset

Press the MENU button for at least 5
seconds to activate offset mode

Use DOWN and UP buttons until is shown on the display.

Press the ENTER button so the display starts blinking.

Use DOWN and UP button to adjust the pan home position.

Once the position has is selected, press the ENTER button to setup OR Automatically return to the offset
functions without any changes by pressing the MENU button
To go back to the main functions without any change wait 8 seconds.
Tilt offset

Press the MENU button for at least 5 seconds to activate offset mode

Use DOWN and UP button until is shown on the display.

Press the ENTER button so the display starts blinking.

Use DOWN and UP button to adjust the tilt home position.
BRITEQ
®
OPERATION MANUAL
(Lamp on) or (Lamp off) mode.
( Lamp mode on ) or ( Lamp mode off ) mode.
8/68 BT-575W