System Specifications - Altec Lansing VS3251 Mode D'emploi

POWERING ON
• After all other connections are made, plug the AC power cord (on the back of
subwoofer) into a wall outlet.
• Turn the system on by pushing the power switch on the back of the
subwoofer. The LED on the subwoofer will blink slowly when the unit is in
stand-by mode.
• Turn on the audio source.
• Insert 2 AAA (LR 03) batteries in the battery compartment of the wireless
remote.
• Activate the system by pushing the
on the subwoofer will stop blinking when the unit is on.
Note: While in stand-by or mute mode, the system continues to receive power.
To completely shut down the unit push the power switch on the back of the
subwoofer and make sure the LED on the subwoofer is off.
Note: To avoid hearing a popping sound when you turn on your Altec Lansing
speaker system, always turn on your audio source first.
Stereo and Surround Sound
• Push the STER/SURR button on the wireless remote to alternate between
six-speaker surround sound and two-speaker stereo sound.
Note: The system will power on the surround mode (SURR), with all five
speakers activated.
Master Volume
The MASTER VOLUME knob on the subwoofer and the "+" and "–" buttons
marked with the word "MASTER VOLUME" on the wireless remote control the
master volume. On the subwoofer, turn the knob clockwise to increase the
volume and counterclockwise to decrease the volume. On the wireless remote,
push the "+" button to increase the volume, and the "–" button to decrease it.
System Specifications*
Altec Lansing's superior sound comes from our patented Dynamic EQ technology, which utilizes custom-built, high-fidelity drivers, state-of-the-art equalization
circuitry, and a harmonious mix of the following specifications:
Sound Pressure Level (SPL):
Total Continuous Power:
• Front Speakers:
• Rear Speakers:
• Center Speaker:
• Subwoofer:
*Power rating conforms to FTC Amplifier Rule #16 C.F.R. Part 432.
located on the wireless remote. The LED
101 dB
70 Watts RMS
9 Watts/channel @ 4 ohms
@ 10% THD @ 120 Hz – 17 kHz
2 Channels Loaded
9 Watts/channel @ 4 ohms
@ 10% THD @ 120 Hz -– 17 kHz
2 Channels Loaded
9 Watts @ 4 ohms
@ 10% THD @ 120 Hz – 17 kHz
Single Channel Loaded
25 Watts @ 4 ohms
@ 10% THD @ 40 – 170 Hz
Single Channel Loaded
Surround Volume
The "+" and "–" buttons marked with the word "REAR" on the wireless remote
control the volume of the rear speakers. Push the "+" button to increase the
volume, and the "–" button to decrease it.
Center Volume
The "+" and "–" buttons marked with the word "CENTER" on the wireless
remote control the volume of the center speaker. Push the "+" button to increase
the volume, and the "–" button to decrease it.
Subwoofer Volume
The "+" and "–" buttons marked with the word "SUBWOOFER" on the wireless
remote control the volume of the subwoofer. Push the "+" button to increase the
volume, and the "–" button to decrease it.
Mute
To mute the speaker system, press the MUTE button located on the wireless
remote. The LED on the subwoofer will blink fast when the unit is in
mute mode.
Headphones
To use headphones with the system, plug them into the labeled
subwoofer. When headphones are connected, the speaker system is muted.
Frequency Response:
Signal to Noise Ratio
@ 1 kHz input:
Drivers (per satellite):
Subwoofer:
5
40 Hz – 17 kHz (-10 dB)
> 70 dB
One full-range 2.5" driver per speaker
One 5" long-throw woofer
jack on the