Safety Rules; Work Area - Hilti TE 6-A Mode D'emploi

Technical data for the battery
(accessory B36 / 2.4
TE 6-A Li) Li-Ion
Voltage 36 V
Battery capacity 36 V x
2.4 Ah
= 86,4 Wh
Weight 1.17 kg
Type of cell Lithium-
ion
No. of cells 10
Temperature
monitoring NTC
Deep discharge

prevention
Right of technical changes reserved
Insert tools, accessories
Bit holder
Angular chuck
Charger
Battery
The tool is designed for the following uses:
Use
Drilling in concrete, masonry and
natural stone
Setting anchors
Drilling in wood and metal
Screwdriving
Using hole saws in wood, plastic,
tiles and masonry
Drilling in snow, ice and hard
ground

Safety rules

1. General safety rules
-WARNING- Read all instructions! Failure to follow
all instructions listed below may result in electric shock,
fire and/or serious injury. The term "power tool" in all
of the warnings listed below refers to your mains oper-
ated (corded) power tool or battery operated (cord-
less) power tool.
Printed: 07.07.2013 | Doc-Nr: PUB / 5071061 / 000 / 00
B36 / 2.6 B36 / 3.0
Li-Ion Li-Ion
36 V 36 V
36 V x 36 V x
2.6 Ah 3.0 Ah
= 93,6 Wh = 108,0 Wh
1.17 kg 1.17 kg
Lithium- Lithium-
ion ion
10 20
NTC NTC
 
for NiCd and NiMH batteries
for Li-ion batteries
for the TE 6-A
for the TE 6-A Li
Required insert tool
Drill bit with TE-C connection end
Anchor setting tool with TE-C
connection end
Quick-release chuck or key-type
chuck
S-BHU 75 M SDS bit holder
Quick-release chuck or key-type
chuck
TE-C-EB ice drill bit
SAVE THESE INSTRUCTIONS

1.1 Work area

a) Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
b) Do not operate power tools in explosive atmos-
pheres, such as in the presence of flammable liq-
uids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
B36 / 3.3 B 36 / 3.9
Li-Ion Li-Ion
36 V 36 V
36 V x 36 V x
3.3 Ah 3.9 Ah
= 118,8 Wh = 140,4 Wh
1.6 kg 1.65 kg
Lithium- Lithium-
ion Iion
30 30
NTC NTC
 
S-BH 50
TE-AC
TCU 7/36
C 7/36-ACS
C 4/36
C 4/36-ACS
BP6-86
B36 / 2.4 NiCd
B36 / 2.4 Li-Ion
B36 / 2.6 Li-Ion
B36 / 3.0 Li-Ion
B36 / 3.3 Li-Ion
B36 / 3.9 Li-Ion
B36 / 2.4 NiCd
Diameter range
Drilling in concrete: 4–16 mm dia.
All Hilti anchors with TE-C setting
tools
Wood drill bits up to 20 mm dia.
Metal drill bits up to 10 mm dia.
TE-HS hole saws 25–105 mm dia.
28–35 mm dia.
B36 / 2.4
NiCd
36 V
36 V x
2.4 Ah
= 86,4 Wh
en
2.08 kg
Nickel-
cadmium
30
NTC
13