Changing Tools - Festool OF 1010 REBQ Notice D'utilisation

English
must be switched off and then switched back on
again.
Due to the built-in restart protection, the power
tool cannot be switched on and off via an exter­
nal switch module.
Brake
The OF 1010 REBQ has an electronic brake
which brings the spindle with tool to a standstill
within approx. 2 seconds of the tool being
switched off.
7.2

Changing tools

CAUTION
Risk of injury from hot and sharp insertion
tool
► Do not use any blunt or faulty insertion
tools.
► Wear protective gloves when handling an
insertion tool.
To change tools, place the power tool on its
side.
Inserting the tool
► Insert the routing tool into the open collet
as far as possible or at least up to the
mark on the router shank.
► Turn the spindle until the spindle stop [1-6]
engages when pressing and the spindle
locks.
► Tighten the nut [1-5] using an open ended
spanner (WAF 19).
Removing the tool
► Turn the spindle until the spindle stop [1-6]
engages when pressing and the spindle
locks.
► Undo the nut [1-5] using an open ended
spanner (WAF 19) until you can feel resist­
ance. Overcome the resistance by continu­
ing to turn the open ended spanner.
► Remove the router.
7.3 Changing the collets
Collets are available for the following shaft di­
ameters: 6.0 mm; 6.35 mm; 8.0 mm (See
Festool catalogue or online at www.festool.com
for the order numbers)
► Completely unscrew the nut [1-5] and re­
move it together with the collet.
► Only insert a new collet into the spindle if a
nut is fitted and engaged.
► Gently screw in the nut. Do not tighten the
nut if no cutter is inserted.
18
7.4 Setting the routing depth
The routing depth is set in three steps:
1. Set the zero point, see 7.5.
2. Specify the routing depth, see 7.6.
3. Clamp the routing depth, see 7.7.
7.5 Setting the zero point
► Release the clamp lever [1-8] so that the
depth stop [1-3] can move freely.
► Position the router with the router ta­
ble [1-1] on a level surface. Open the rotary
knob [1-7] and push the power tool down­
wards until the cutter sits on the surface.
► Clamp the power tool in this position by
closing the rotary knob [1-7].
► Press the depth stop [1-3] against one of
the three fixed stops of the rotatable step­
ped stop [1-2].
A hex key can be used to individually adjust the
height of each fixed stop.
► Push the indicator [1-10] downwards so
that it points to 0 mm on the scale.
If the zero position is incorrect, this can be
corrected using the screw on the indica­
tor [1-10].
7.6 Specifying the routing depth
The required routing depth can be specified us­
ing either quick depth adjustment or fine depth
adjustment.
Quick depth adjustment
► Pull the depth stop [1-3] upwards until the
indicator [1-10] points to the required rout­
ing depth.
► Clamp the depth stop in this position using
the clamp lever [1-8].
Fine depth adjustment
► Clamp the depth stop using the clamp lev­
er [1-8].
► Set the required routing depth by turning
the adjusting wheel [1-9].
Turning the adjusting wheel by a mark
changes the routing depth by 0.1 mm. A
full rotation changes the routing depth by
1 mm. The maximum adjustment range for
the adjusting wheel is 8 mm.
7.7 Clamping the routing depth
► Open the rotary knob [1-7] and push the
power tool down until the depth stop touch­
es the fixed stop.
► Clamp the power tool in this position by
closing the rotary knob [1-7].