Available Accessories; Protection Of The Envi- Ronment; Trouble Shooting - Metabo PK 255 Instructions D'utilisation Originales

ENGLISH

13. Available accessories

For special tasks the following accesso-
ries are available at your specialised
dealer – see back cover for illustrations:
A Wheel Set
B Base Support System
C Extension incl. support leg for base
support system
D Additional support leg for base sup-
port system
E Sliding Carriage 
For convenient guiding of long
stock.
For installation on the left or right
side of the base support system
F Table Side Extension Plus
Increases the bearing surface; ide-
al for cutting boards
For installation on the left or right
side of the base support system
G Table extension
H Mitre Fence
For making precise cross and mitre
cuts
I Roller Stand RS 420
J Roller Stand RS 420 W
K Roller Stand RS 420 G
L Care and Maintenance Spray 
For removing resin residue and pre-
serving metal surfaces.
M Suction Adapter 
For connection to a dust collector.
N Handgrip for push block
For guiding the workpiece laterally
Available Saw Blades
O Saw blade
TCT/CT 250 × 2.8 / 2.0 × 30, 25°
24 alternate top bevel teeth
Suitable for solid wood and for
rough cuts in composite materials
and coated wood
P Saw Blade
TCT/CT 250 × 2.8 / 1.8 × 30, 15°
34 alternate top bevel teeth
Suitable for softwood and hard-
wood, 
Suitable for solid and laminated
wood, particle board (raw coated or
veneered), MDF and composite ma-
terials
Q Saw Blade
TCT/CT 250 × 2.8 / 1.8 × 30, 15°
36
42 alternate top bevel teeth
Suitable for softwood and hard-
wood, 
Suitable for solid and laminated
wood, particle board (raw coated or
veneered), MDF and composite ma-
terials
R Saw Blade
TCT/CT 250 × 2.8 / 1.8 × 30, 15°
60 alternate top bevel teeth
Suitable for softwood and hard-
wood, 
Suitable for solid and laminated
wood, particle board (raw coated or
veneered), MDF and composite ma-
terials
S Saw Blade
TCT/CT 250 × 3.2 / 2.2× 30, 10°
60 alternate top bevel teeth
Suitable for softwood and hard-
wood, 
Suitable for solid and laminated
wood, particle board (raw coated or
veneered), MDF and composite ma-
terials
T Saw Blade 
TCT/CT 250 × 2.8 / 1.8 × 30, 10°
80 alternate top bevel teeth
For superior cut quality, e.g. in lami-
nate and in plastic, aluminium, cop-
per and brass extrusions,
Perfect cutting results for solid wood
and for raw, coated or veneered
particle board and MDF
U Saw Blade 
TCT/CT 250 × 2.8 / 2.0 × 30, 5°
neg.
80 trapezoid/flat teeth
For superior cut quality, e.g. in lami-
nate and in plastic, aluminium, cop-
per and brass extrusions,
Perfect cutting results for solid wood
and for raw, coated or veneered
particle board and MDF
14. Protection of the Envi-
ronment
The machine's packing can be 100%
recycled.
End-of-life power tools and accessories
contain large amounts of valuable raw
materials and plastics which must be
recycled.
This manual was printed on chlorine-
free bleached paper.

15. Trouble Shooting

A
Danger!
Before carrying out any fault service
or maintenance work, always:
1. Switch machine OFF
2. Unplug mains cable.
3. Wait for saw blade to come to
standstill.
Check that all safety devices are
operational again after each fault
service.
Motor does not run
Undervoltage relay tripped by power
failure:
switch on again.

No mains voltage
 check cables, plug, outlet and
mains fuse.
Motor overheated, e.g. by a blunt saw
blade or chip build-up in the chip case:
 remove cause for overheating, let
cool down for a few minutes, then
start again.
Motor supply voltage too low:
use a shorter supply line or supply

line with a larger lead cross section
2
( 1.5 mm ).
 have power supply checked by a
qualified electrician.
Loss of cutting performance
Saw blade blunt (possibly tempering
marks on blade body):
Saw blade not suitable for material
being cut (see section 'Technical Da-
ta');
Saw blade warped:
 Replace saw blade (see chapter
"Maintenance").
Saw dust build-up
No dust collector or dust collector of in-
sufficient capacity connected (see
"Connecting the dust collector" in chap-
ter "Installation"):
 connect dust collector, or
 increase suction capacity.