Assembly Safety Checks; Final Safety Checks; Ec Declaration Of Conformity - Evolution R255 SMS Notice Originale

ASSEMBLY SAFETY CHECKS

PART CONDITION
Slides Inserted through the bevel neck and connected to the
cutting head. Locating lugs successfully deployed.
Mitre Handle Locking Knob Installed into mitre handle / rotary table.
Slide Carriage Inserted into the threaded hole in the bevel neck. Anti-vibration
locking screw spring fitted beneath the locking screw hand knob.
Power Cable Routed correctly with cable guide/clamps
correctly installed.
Blade Blade correctly installed and with the rotation arrows on the
blade and on the machine matching. Outer blade flange and
arbor bolt and washer correctly fitted.
Safety Guards Lower Safety Guard fully operational. cutting head locks in
the upper position with blade covered. cutting head can only
be lowered when Blade Guard Locking Lever is operated.
Supply Supply matches specification found on machine Rating Plate.
Plug matches power source outlet.
Mounting Either:
a) Machine permanently sited and bolted to workbench.
b) Machine mounted on board which can be clamped
to workbench.
c) Machine is bolted to a dedicated mitre saw Stand.
Sited Adequate provision made for the handling of long or
irregular shaped work-pieces.
Environment Dry, clean and tidy. Temperature conducive to material
handling. Lighting adequate (double banked if fluorescent
lights are used).
All the Yes Boxes must be ticked before the machine can be used. No tick = No use.

FINAL SAFETY CHECKS

PART CONDITION
Assembly Repeat the Assembly Safety Checks.
Operation With the machine switched off and disconnected from the mains supply,
carry out the following procedures:
• Set the machine to each of its maximum operational settings in turn.
• At each setting lower the cutting head to its lowest position,
observing the path of the blade as you do so.
• Check that the blade does not interfere or strike any part of the
machine, castings or guards as the cutting head is lowered.
• Check that when the sliding carriage is employed no contact
between the cutting head and the blade and other parts of the
machine occurs.
• Spin the blade by hand (it is advisable to wear gloves whilst doing
this, but not when the saw is being used operationally).
• Check that the blade rotates smoothly with no unusual noises, and
that there is no contact between the blade and the upper and lower
blade guards.
• Check that there is no discernible blade 'wobble' in any direction as
the blade rotates.
All the Yes Boxes must be ticked before the machine can be used. No tick = No use.
34
www.evolutionpowertools.com
YES
YES
www.evolutionpowertools.com

EC DECLARATION OF CONFORMITY

The manufacturer of the product covered by this Declaration is:
Evolution Power Tools, Venture One, Longacre Close, Holbrook Industrial Estate, Sheffield, S20 3FR.
The manufacturer hereby declares that the machine as detailed in this declaration fulfils all
the relevant provisions of the Machinery Directive and other appropriate directives as detailed
below. The manufacture further declares that the machine as detailed in this declaration, where
applicable, fulfils the relevant provisions of the Essential Health and Safety requirements.
The Directives covered by this Declaration are as detailed below:
2006/42/EC
Machinery Directive.
2014/30/EU.
Electromagnetic Compatibility Directive,
2011/65/EU. & The Restriction of the Use of certain
2015/863/EU.
Hazardous Substances in Electrical Equipment (RoHS) Directive
2012/19/EU. The Waste Electrical and Electronic Equipment (WEEE) Directive
And is in conformity with the applicable requirements of the following documents
EN 62841-1:2015 • EN 62841-3-9:2015/A11:2017 • EN ISO 12100:2010
AfPS GS 2014:01 PAK • EN 55014-2: 2015 • EN 61000-3-3: 2013
EN 55014-1:2006/A2:2011 • EN 61000-3-2:2014 • EN 55014-1:2017
Product Details
Description: 255mm MULTI-MATERIAL SLIDING MITRE SAW
Evolution Model No: R255SMS: 052-0001 / / 052-0002 / 052-0003
R255SMS+: 052-0001A / 052-0002A / 052-0003A
Brand Name: EVOLUTION
Voltage: 220-240V / 110V ~ 50 Hz
Input: 2000W (220-240V) / 1600W (110v)
The technical documentation required to demonstrate that the product meets the requirements of
directive has been compiled and is available for inspection by the relevant enforcement authorities,
and verifies that our technical file contains the documents listed above and that they are the correct
standards for the product as detailed above.
Name and address of technical documentation holder.
Signed: Print: Barry Bloomer
Supply Chain & Procurement Director
Date: 14/05/2018
Evolution Power Tools, Venture One, Longacre Close, Holbrook Industrial Estate, Sheffield S20 3FR
35
EN
ES
DE
FR
IT
PL
PT
RO