Bosch BRC3600 Notice D'utilisation D'origine page 13

Level Colour Notes
TURBO Red Maximum support even at a high ca-
dence, for sport cycling
The designations and configuration of the assistance levels can be
preconfigured by the manufacturer and selected by the bicycle re-
tailer.
Interaction between the eBike system and gear-
shifting
The gear shifting should be used with an eBike drive in the
same way as with a normal bicycle (observe the operating in-
structions of your eBike on this point).
Irrespective of the type of gear shifting, it is advisable that
you briefly reduce the pressure on the pedals when changing
gear. This will aid gear shifting and reduce wear on the
powertrain.
By selecting the correct gear, you can increase your speed
and range while applying the same amount of force.
Switching bike lights on/off
Check that your bike lights are working correctly before
every use.
To switch on the bike lights, press the (9) button for more
than 1 s.
You can use the (11) and (10) buttons to control the bright-
ness of the LEDs on the operating unit.
Switching the push assistance on/off
The push assistance aids you when pushing your eBike. The
speed in this function depends on the selected gear and can
reach a maximum of 6 km/h. The lower the selected gear,
the lower the speed of the push assistance function (at full
power).
The push assistance function must only be used when
u
pushing the eBike. There is a risk of injury if the wheels
of the eBike are not in contact with the ground while using
the push assistance.
To start walk assistance, press the (8) button for more than
1 s and keep it pressed. The battery charge indicator (3)
goes out and a white moving light in the direction of travel
shows that it is ready.
To activate walk assistance, one of the following actions
must occur within the next 10 s:
– Push the eBike forwards.
– Push the eBike backwards.
– Perform a sideways tilting movement with the eBike.
After activation, the motor begins to push and the continu-
ously filling white bars change colour to ice-blue.
If you release the (8) button, walk assistance is paused. You
can reactivate walk assistance within 10 s by pressing the
(8) button.
If you do not reactivate walk assistance within 10 s, walk as-
sistance automatically switches off.
Walk assistance is always ended if:
– the rear wheel jams;
– the bicycle cannot move over ridges;
Bosch eBike Systems
– a body part is blocking the bike crank;
– an obstacle continues to turn the crank;
– you start pedalling;
– the (9) button or on/off button (1) is pressed.
The push assistance function is subject to local regulations;
the way it works may therefore differ from the description
above, or the function may even be deactivated completely.
ABS – anti-lock braking system (optional)
If the bicycle is equipped with a Bosch eBike ABS, the ABS
LED (4) lights up when the eBike system starts.
If the eBike reaches a speed of 6 km/h, the ABS LED (4)
goes out.
In the event of a fault, the ABS LED (4) lights up together
with the orange flashing assistance level LED (5). You can
acknowledge the error with the select button (2); the flash-
ing assistance level LED (5) goes out. The ABS LED (4) con-
tinues to light up to show that the ABS system is not in oper-
ation.
For details on the ABS and how it works, please refer to the
ABS operating instructions.
Establishing a smartphone connection
In order to be able to use the following eBike functions, a
smartphone with the eBike Flow application is required.
Connection to the app occurs via a Bluetooth® connection.
Switch on the eBike system and do not start riding the eBike.
Begin Bluetooth® pairing by long pressing (> 3 s) the on/off
button (1). Release the on/off button (1) as soon as the top-
most bar on the battery charge indicator shows the pairing
process by flashing blue.
Confirm the connection request in the app.
Activity tracking
In order to record activities, it is necessary to register and
log into the eBike Flow app.
To record activities, you must consent to the storage of your
location data in the app. Without this, your activities cannot
be recorded in the app. For location data to be recorded,
you must be logged in as the user.
Lock function
The lock function can be set up and configured via the eBike
Flow app. This stores a digital key on the smartphone, which
is required to start the eBike system.
Once the lock function is switched on, the eBike can only be
put into operation if:
– the configured smartphone is switched on;
– the smartphone has sufficient battery charge;
– and the smartphone is in the immediate vicinity of the op-
erating unit.
Otherwise, motor support remains switched off.
If the key is not verified immediately, the search for the key
is shown by the battery charge indicator (3) and the assist-
ance level LED (5) flashing white. If the key is found, after
flashing white the state of charge of the battery and the last
set assistance level is displayed.
English – 3
0 275 007 3RL | (09.07.2021)