Remaining Risk Factors - HOLZMANN MASCHINEN KAP 305ECO Mode D'emploi

 Rotating parts can cause severe cut injuries
 Keep the saw blades sharp and clean, so they get stuck less often and are easier to
guide
 Keep any machine that is not being used out of reach of children
 Connect the dust extraction device to
 Do not use the cable to remove the plug from the socket.
 Protect the cable from heat, oil and sharp edges
 Even Lasers with relatively small output can harm your eyes! Therefore:
 Never look directly into the laser or into the laser beam!
 Never direct the laser beam towards reflecting surfaces, persons and animals.
 Do not manipulate the laser device!!
 Use only saw blades that are suitable for the use with the machine, especially regarding
technical parameters and which are tested and comply with the directive EN 847-1.
 Deflected, defect or worn saw blades have to be replaced immediately.
 Blunt saw blades have to be sharpened or replaced.
 Blunt saw blades highly increase the danger of kickback!
 Assure yourself that the saw blade is correctly mounted and does not touch the base
plate.
 Do not stop the saw blade by touching it on the side. This will ruin the drive mechanism.
 Do not manipulate or remove the saw blade protecting cover!
 Do not fix small workpieces by hand, instead only use the downholder.
 No material feed, no material removal, no adjustments or other activities when saw
blade is running.
 Do not position your hands near the saw blade or in a way that they could slip into the
cutting line.
 Long workpieces have to be supported by the double bar guide.
 Take especially care when cutting round workpieces!
 Check the workpiece for nails, clamps and other material!
 Just cut one workpiece at once. Do not stack or attempt to cut several work-pieces in
one cutting operation!
 Do not cut firewood
 Wear gloves when handling the saw blades and rough materials. It is recommended
that saw blades, whenever practicable be carried in a container.
 Make sure that the speed indicated on the saw blade is at least as high as that on the
saw speed specified.
 Be sure to use only those spacers and screw rings, which are suitable for the purpose
specified by the manufacturer.
 No reload, remove or adjust workpieces, or material remains with the machine running!
 Do not place hands in near circular saw blade or in a position where they could slip
direction circular saw blade!
 The use of other application tools and other accessories can mean a risk of personal
injury.
 Let your power tool repaired by a qualified electrician
 The machine does not require extensive maintenance. If malfunctions and defects
occur, let it be serviced by trained persons only.

12.4 Remaining risk factors

It is important to ensure that each machine has remaining risks.
In the execution of all work (even the simplest) greatest attention is required. A
safe working depends on you!
Even if the machine is used as required it is still impossible to eliminate certain residual risk factors totally.
The following hazards may arise in connection with the machine´s construction and design:
Despite of correct and proper use and maintenance there remain some residual risk factors:
 Risk of injury to the hands / fingers by the rotating tool during operation.
 Risk of injury due to sharp edges of the workpiece, especially in non-fixed with a suitable tool /
device workpiece.
 Risk of injury: hair and loose clothing, etc. can be captured and wound up! Safety regulations
must be observed with regard to clothing.
 Risk of injury due to contact with live electrical components.
 Risk of injury due to breakage or cracking of the abrasive
 Risk of injury due to dust emissions, treated with harmful agents workpieces
 Risk of injury to the eye by flying debris, even with safety goggles.
 Risk of injury to the hearing by prolonged labor without hearing protection.
These risk factors can be minimized through obeying all security and operation instructions, proper machine
maintenance, proficient and appropriate operation by persons with technical knowledge and experience.
HOLZMANN MASCHINEN GmbH www.holzmann-maschinen.at
W A R N I N G
SAFETY
24
KAP 305ECO