Candy PVD 633 Notice D'emploi Et D'installation page 12

• STARTING A COOKING ZONE
- Press the selection button of
the required cooking zone. In
the display zone, the control
LED is on steady. It shows that
the zone is live.
- Press the - or + button to select a heat level between 1 and
9. Hold down the + or - button and the heat level increases
or decreases gradually.
The following examples are for information only. Personal
experience should then let you adapt these settings to your taste
and habits.
0 : Off
1 : )
2 : ) ..... Melting heat
3 : Keeping hot
4 : Heating up
5 : Thawing, stewing, full cooking, low temperature
cooking
6 : Cooking without lid
7 : Frying, meat browning and roasting
8 : High temperature cooking and roasting, seizing
9 : Frying, boiling large quantities of water.......
• STOPPING A COOKING ZONE
- Press the selection button of the required cooking zone.
- Press the - button to display heat level
off, the indicator goes off after 10 seconds.
- To stop rapidly, press the - and + buttons at the same time.
The heat level automatically goes down to
The cooking zone goes off.
• GENERAL STOP
The cooking zones and the timer can be stopped at any
moment by pressing the On-Off button.
• RESIDUAL HEAT INDICATOR
The control panel tells the user when the surface temperature of
the cooking zones exceeds about 60°C, by the following displaying:
. When the temperature goes back below 60°C, the
goes off.
For ending the cooking, we advise switching off the cooking zone
and using the residual heat of the zone to finish cooking gently.
N.B. After a cut in the current, the residual heat indicator disappears
completely, even if the surface temperature exceeds 60°C.
• OPERATING THE ADDITIONAL COOKING ZONE
(TWO ZONES)
The cooking zone with two zones is fitted certain models. It can
be either concentric or extendable.
It is active in totality when the cooking zone is in function ;
the control led of the additional cooking is displayed.
To desactivate the additional cooking zone :
- Press on the additional cooking zone button
control led for the additional cooking zone goes off when it is
desactivated.
To re-activate the additional cooking zone :
- Press on the additional cooking zone button
control led for the additional cooking zone is active.
• O P E R AT I N G T H E A D D I T I O N A L C O O K I N G Z O N E
(THREE ZONES)
The additional cooking zone is fitted only one model.
It is active in totality when the cooking zone is in function ;
the two control leds of the additional cooking are displayed.
To desactivate the additional cooking zones :
- Press one time the additional cooking zone button
corresponding control led for the external additional cooking
zone goes off when it is desactivated.
- Press two times the additional cooking zone button
corresponding control led for the central additional cooking zone
goes off when it is desactivated.
To re-activate the additional cooking zones :
- Press on the additional cooking zone button, one or two times
on the additional cooking zone button, according to the need.
. Now the zone goes
.
display
. The corresponding
. The corresponding
. The
. The
11 GB
• PROGRAMMING A COOKING ZONE
Every cooking zone can be programmed for a maximum time of
99 minutes.
- Start the required zone by following the previous instructions.
The control LED near the heat level must be displayed, it shows
that the zone is live.
- Press the Timer button.
The zone mark around the timer display shows the controlled
zone.
- Press again on the timer button to select a time in minutes
between 0 and 99 minutes or press on the "-" button to decrease
the time between 60 minutes and 0.
the programmed time can be modified at any moment reactivating
the cooking zone and then the timer button.
When the time is run, the cooking zone goes off automatically and
an audible beep sounds for 1 minute, press the timer button to
stop it.
the time can be used alone as reminder, it will ring at the end of
the programmed time.
• LOCKING BUTTON OPERATION
The locking function holds the current settings, or prevents anyone
from starting the hob. It is also used for cleaning the control strip
as the controls can be locked without the hob being on.
To lock the hob :
- Press the on/off button
- Press simultaneously " - " button and " + " button of the front
right zone (PVD 633 front left zone), and then press again on
the " + " button of this zone. The hob is locked, the locking
indicator " L " is displayed on all zones for 20 seconds.
To unlock the hob :
- Press the on/off button . The locking indicator " L " is displayed
on all zones.
- Press simultaneously the " - " button and the " + " button of the
front right zone (PVD 633 front left zone), and then press again
on the " - " button of this zone.
The hob is unlocked.
• FAST HEATER OPERATION
Starting the fast heater
- Press the on/off button
- Start the required zone, press the " + " button to obtain position
"9", release the button briefly and press again the " + " button ;
the display alternates showing "A" "fast heater" and "9" heat
level.
- If necessary reduce to the required heat position, the display
alternates showing "A" "fast heater" and the new heat position.
Cooking Power
position released
(%)
0 : 0 %
1 : 3 %
2 : 6 %
3 : 11 %
4 : 16 %
5 : 19 %
6 : 32 %
7 : 45 %
8 : 65 %
9 : 100 %
E.g. 1800 W zone at position 6 = 32% of 1800 W power released
When the "Fast heater" is on, the zone supplies 1800 W power
for 2.5 minutes, and adjusts to 576 W after this time.
* For increased safety, the cooking zones cut off automatically if
they are left on too long. The cut off depends on the heat level
used.
To desactivate the fast heater
- Switch on the cooking zone, press the " - " button to come back
to a normal heat level, decrease to the heat level required or to
" 0 " to stop the cooking zone.
.
.
Time of Maximum
fast heater operating
(minutes) time before
automatic
cut off*
: 0 :
: 1 :
: 3 :
: 5 :
: 6,5 :
: 8,5 :
: 2,5 :
: 3,5 :
: 4,5 :
: 0 :
0 H
6 H
6 H
5 H
5 H
4 H
1,5 H
1,5 H
1,5 H
1,5 H