Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch PKS 16 Multi Notice Originale

OBJ_BUCH-1837-005.book Page 22 Thursday, June 16, 2016 11:13 AM
22 | English
Working with an Auxiliary Stop (see figure E)
For sawing large workpieces or straight edges, a board or lath
can be fastened to the workpiece as an auxiliary stop, and the
power tool can be guided by its base plate alongside the aux-
iliary stop.
Cutting Marks (see figure E)
The "CutControl" viewing window 7, which folds out to the
front, is used for precise guiding of the power tool alongside
the cutting line on the workpiece.
The cutting mark 19 indicates the position of the application
tool for right-angled cuts.
For a dimensionally accurate cut, position the power tool
against the workpiece as shown in the figure. It is recom-
mended to carry out a test cut.
Plunge Cuts (see figure D)
The marks on the base plate indicate the cutting edge on the
workpiece at maximum cutting depth.
– Place the base plate 3 on the working surface. Make sure
that the rear mark on base plate 3 corresponds with the
beginning of the cutting line.
– Switch the power tool on and wait until the saw blade 14
has reached its operating speed.
– Plunge the saw blade 14 slowly into the workpiece. Plung-
ing in too quickly can lead to kickback. Guide the machine
alongside the cutting line. Do not pull the machine toward
the rear!
– When reaching the end of the cutting line, lift the power
tool from the workpiece, and leave it switched on for a few
seconds.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself, pull the mains
plug.
 For safe and proper working, always keep the machine
and ventilation slots clean.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
The blade guard 6 must always move freely and retract auto-
matically. Therefore, always keep the area around the blade
guard 6 clean. Remove dust and chips/shavings using a brush
or by blowing out with compressed air.
Saw blades that are not coated can be protected against cor-
rosion with a thin coat of acid-free oil. Before use, the oil must
be removed again, otherwise the wood will become soiled.
Resin and glue residue on the saw blade produces poor cuts.
Therefore, clean the saw blade immediately after use.
After finishing work, dismount the clamping fixtures and clean
all clamping parts as well as the protective cover.
1 609 92A 216 | (16.6.16)

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-Mail: bsctools@icon.co.za
Bosch Power Tools