Other Information - Sony SU-WH500 Mode D'emploi

Install the Wire Bracket.
2
Peel the Paper Template M from the wall, and secure the Wire
Bracket A to the wall.
A For thick walls
1 Insert the Anchors A F into the holes of the wall.
2 Secure the Wire Bracket A with the four Wood Screws
(φ5×65) G to the wall.
B For thin walls
1 Insert the Anchors B H with the metal parts turned towards
the holes of the wall.
2 Pull the Anchors B H and confirm that they do not come out
from the wall.
3 Push the cap of the Anchor B H into the wall.
4 Shift the upper and lower tips of the Anchor B H to the front
and back, and then stretch the two handle pieces up and
down until they touch the wall.
5 The two handle pieces are torn out, and the Anchor B H is
fixed in the wall.
6 Secure the Wire Bracket A with the four Screws (M5×60)
I to the wall.
3 Prepare for the installation of the TV
Make sure that your TV has the Table-Top Stand attached, and the
TV is not tilted (at an angle of 0°). If your TV has a terminal cover
or a bottom cover attached, remove it before carrying out the
procedure below.
For details, refer to your TV's operating instructions.
When using an electric screwdriver, set the torque setting to
approximately 1.5 N•m {15 kgf•cm}.
Attach the Cushions.
1
Attach one Cushion A K to each Pulley B, and attach two
Cushions B L each to the Tilt-up Bracket C and the Belt
Bracket D, respectively.
If you use the Home Theatre System HT-CT350
Also attach the remaining Cushions to each Cushion that has
already been attached to the two Pulleys, Tilt-up Bracket, and
Belt Bracket respectively.
Remove screws from the rear of your TV.
2
If your TV has four screws tightened on the rear, remove all of
them. Refer to your TV's operating instructions for details.
Attach the Pulleys.
3
Tighten the Pulleys B with Screws (M6×18) J to the upper two
screw holes on the rear of your TV.
Attach the Tilt-up Bracket.
4
Tighten the Tilt-up Bracket C with Screw (M6×18) J to the
bottom right screw hole on the rear of your TV.
Attach the Support Belt.
5
Align the Support Belt E* between the two sides of the Belt
Bracket D, and adjust the position of the Support Belt E so that
at least one hole of it hangs down below the bottom edge of the
TV.
Tighten it with Screw (M6×18) J to the bottom left screw hole
on the rear of your TV.
* Installation of the Support Belt E on the wall is recommended
for safety.
Connect the AC power cord and connecting cables.
6
For details, refer to your TV's operating instructions.
4 Install your TV on the wall
Remove the Table-Top Stand.
1
For details, refer to your TV's operating instructions.
Hang your TV on the wire of the Wire Bracket.
2
Be sure that two or more persons hold the TV, each person using
both hands. Hang the axles of both Pulleys B installed to the TV
onto the wire firmly.
Adjust the slant of your TV.
3
Move your TV right or left as you look at its front, so as to adjust
it horizontally.
Prevent your TV from falling.
4
Tighten the Support Belt E with the Anchor A F and the Wood
Screw (φ5×65) G (for thick walls), or with the Anchor B H and
the Screw (M5×60) I (for thin walls) to the wall.
Confirm the completion of the installation
Check the following points.
• The axles of both Pulleys B are firmly hung onto the wire.
• The cord and the cable are not twisted or pinched.

Other information

To disconnect the cables
Use the Tilt-up Bracket C to tilt your TV to the front to easily
disconnect the cord and cables with the TV still hung to the wall.
~
If your TV is XBR-60LX90s* or KDL-60LX90s*/60NX80s*, the
Tilt-up Bracket C cannot be tilted.
* In the actual model names, the "s" indicates numbers and/or
characters specific to each model.
C
5
(GB)