Commissioning; Technical Data - OHIO SEMITRONICS DMT-1000 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

7. Commissioning

Prior to starting, check that the connection
data of the transducer agrees with the system
data (see type label).
The power supply to the transducer can then be switched
on and the signals applied to the measuring inputs.
Label Identification:
1
Input voltage
2
Input current
3
Nominal frequency
4
Power supply
5
Baud Rate

7.1 Technical data

Symbols
Symbols
Meaning
X
Measured variable
X0
Lower limit of the measured variable
X1
Break point of the measured variable
X2
Upper limit of the measured variable
Y
Output variable
Y0
Lower limit of the output variable
Y1
Break point of the output variable
Y2
Upper limit of the output variable
V
Input voltage
Vr
Rated value of the input voltage
V12
Phase-to-phase voltage L1 – L2
V23
Phase-to-phase voltage L2 – L3
V31
Phase-to-phase voltage L3 – L1
V1N
Phase-to-neutral voltage L1 – N
V2N
Phase-to-neutral voltage L2 – N
V3N
Phase-to-neutral voltage L3 – N
VM
Average value of the voltages
(V1N + V2N + V3N) / 3
I
Input current
I1
AC current L1
I2
AC current L2
I3
AC current L3
Ir
Rated value of the input current
IM
Average value of the currents
(I1 + I2 + I3) / 3
IMS
Average value of the currents and sign
of the active power (P)
IB
RMS value of the current with wire setting
range (bimetal measuring function)
IBT
Response time for IB
Ohio Semitronics, Inc.
8
7004-00090-A Rev 2/00
6
Model Number
7
Test and Conformity marks
8
Input Terminals
9
Output Terminals
10 Output Values
Page 8 of 24
7
DMT-1000
6
Multifunction Transducer
1
Volts
2 11
4
15 16 17 18 19 20 21 22 23 24 25 26
M :
M :
1
2
M :
M :
3
4
10
I V I
I V I
1+
1
1
2+
2
1 2 3
4
5 6 7
Fig. 9. Declaration to type label.
Symbols
Meaning
BS
Slave pointer function for the measurement of
the RMS value IB
BST
Response time for BS
ϕ
Phase-shift between current and voltage
F
Frequency of the input variable
Fn
Rated frequency
P
Active power of the system
P = P1 + P2 + P3
P1
Active power phase 1
(phase-to-neutral L1 – N)
P2
Active power phase 2
(phase-to-neutral L2 – N)
P3
Active power phase 3
(phase-to-neutral L3 – N)
Q
Reactive power of the system
Q = Q1 + Q2 + Q3
Q1
Reactive power phase 1
(phase-to-neutral L1 – N)
Q2
Reactive power phase 2
(phase-to-neutral L2 – N)
Q3
Reactive power phase 3
(phase-to-neutral L3 – N)
S
Apparent power of the system
S = ⎟ I
2
2
+ I
+ I
1
2
S1
Apparent power phase 1
(phase-to-neutral L1 – N)
S2
Apparent power phase 2
(phase-to-neutral L2 – N)
S3
Apparent power phase 3
(phase-to-neutral L3 – N)
Sr
Rated value of the apparent power of the
system
PF
Active power factor cosϕ = P/S
Ohio Semitronics, Inc.
4242 Reynolds Dr.
Hilliard, Ohio USA
2
3
5
Amperes
Baud
Freq.
Aux. Power
85 - 230Vac/dc 50/60Hz 9W
9
+ -
GND
Tx/Rx
CT Ratio
PT Ratio
System
Aux.
Power
I V I
N
+
-
2
3+
3
3
8 9 11 13 14
8
· ⎟ V
2
2
2
2
+ V
+ V
3
1
2
3

Publicité

Chapitres

Table des Matières
loading

Table des Matières