JB Systems Light LASER BURST III Mode D'emploi page 6

ENGLISH
5) DMX512 MODE:
The laser can be controlled by any standard DMX-controller in 2 different DMX-modes:
 1 CHANNEL MODE: for extremely easy setup and use! (display shows "1Ch")
 11 CHANNEL MODE: for full control of all possibilities. (display shows "11C")
 Connect the DMX input of the laser to the DMX output of the previous unit in the chain or directly to the
DMX-output of your controller.
 Press the FUNC-button until the display shows: "1Ch" or "11C".
 Press the UP/DOWN buttons to select the desired DMX-mode. (1Ch or 11C)
 Press the ENTER-button to confirm your choice.
 Press the FUNC-button until the display shows a 3 digit number
 Select the desired DMX-address (from 001 to 505)
 Press the ENTER-button to confirm your choice.
Note: the display blinks when the unit is in DMX-mode and no DMX-signal is detected.
Some more information on DMX512:
The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to
"daisy chain" your DMX controller and all the connected light effects with a good quality XLR M/F balanced
cable. To prevent strange behavior of the light effects, due to interferences, you must
use a 90Ω to 120Ω terminator at the end of the chain. Never use Y-splitter cables,
this simply won't work!
Each effect in the chain needs to have its proper starting address so it knows which
commands from the controller it has to decode.
1 CHANNEL DMX-CONFIGURATION OF THE LASER:
CHANNEL VALUE
000-019 Laser OFF (Black out)
SLD mode (Slow Moving Dots Effect)
020-039
FAD mode (Fast Moving Dots Effect)
040-059
SOD mode (Sound activated Moving Dots Effect)
060-079
080-099 SLL mode (Slow Moving Lines Effect)
CH 1 FAL mode (Fast Moving Lines Effect)
100-119
MODES
SOL mode (Sound activated Moving lines Effect)
120-139
SLP mode (Slow Moving Patterns Effect)
140-159
FAP mode (Fast Moving Patterns Effect)
160-179
180-199 SOP mode (Sound activated Moving patterns Effect)
200-219 SRA mode (Sound activated Random Effect)
ARA mode (Auto Running Random Effect)
220-255
11 CHANNEL DMX-CONFIGURATION OF THE LASER:
IMPORTANT REMARK: DMX Channel1 is used to set the different working modes of the laser.
 To use the laser in full 11 channel mode, channel 1 must be set to value 251 or higher.
JB SYSTEMS
®
USER MANUAL
DESCRIPTION
7/58 LASER BURST III
ENGLISH
CHANNEL VALUE
000-019 Laser OFF (Black out)
ARA mode (Auto Running Random Effect)
020-039
040-059 SRA mode (Sound activated Random Effect)
060-079 SLP mode (Slow Moving Patterns Effect)
FAP mode (Fast Moving Patterns Effect)
080-099
SOP mode (Sound activated Moving patterns Effect)
100-119
CH 1
SLL mode (Slow Moving Lines Effect)
120-139
MODES
FAL mode (Fast Moving Lines Effect)
140-159
160-179 SOL mode (Sound activated Moving lines Effect)
SLD mode (Slow Moving Dots Effect)
180-199
FAD mode (Fast Moving Dots Effect)
200-219
SOD mode (Sound activated Moving Dots Effect)
220-239
240-255 DMX MODE (other channels activated
CH 2
000-255
Motor1 Rotation Speed
M1 ROT. SPEED
CH 3 000-075 Motor1 clockwise rotation
M1 ROTATION
076-150 Motor1 stop
DIRECTION
151-255 Motor1 anti-clockwise rotation
CH 4
000-255
Motor1 Shaking range
M1 SHAKE RANGE
000-056 Motor1 Shaking mode 1
CH 5 057-112 Motor1 Shaking mode 2
M1 SHAKE MODE
113-168 Motor1 Shaking mode 3
169-255 Motor1 Shaking mode 4
CH 6
000-255
Motor2 Rotation Speed
M2 ROT. SPEED
CH 7 000-075 Motor2 clockwise rotation
M2 ROTATION
076-150 Motor2 stop
DIRECTION
151-255 Motor2 anti-clockwise rotation
CH 8
000-255
Motor2 Shaking range
M2 SHAKE RANGE
000-056 Motor2 Shaking mode 1
CH 9 057-112 Motor2 Shaking mode 2
M2 SHAKE MODE
113-168 Motor2 Shaking mode 3
169-255 Motor2 Shaking mode 4
000-028 RED + GREEN
GREEN
029-056
RED
057-084
RED off, strobed GREEN
085-112
CH 10
113-140 GREEN off, strobed RED
COLORS
141-168 RED on, strobed GREEN
GREEN on, strobed RED
169-197
Both RED and GREEN strobed
198-224
225-255 RED and GREEN alternately strobed
CH 11
000-255
Slow to Fast
STROBE
JB SYSTEMS
®
USER MANUAL
DESCRIPTION
8/58 LASER BURST III