Manitowoc Cleveland SGL-30-T1 Manuel De L'opérateur page 4

INSPECTION
1. Before unpacking visually inspect the unit for evidence
of damage during shipping.
2. If damage is noticed, do not unpack the unit, follow
shipping damage instructions.
3. Carefully remove unit from shipping carton. Remove
any packing material from unit. After carefully
unpacking check for "concealed" damage. If damage is
noticed, follow "SHIPPING DAMAGE INSTRUCTIONS"
shown below.
4. A protective material has been applied to the stainless
steel panels. This material must be removed
immediately after installation, as heat will melt the
material and make it more difficult to remove.
SHIPPING DAMAGE INSTRUCTIONS
If shipping damage to the unit is discovered or suspected,
observe the following guidelines in preparing a shipping
damage claim.
1. Write down a description of the damage or the reason
for suspecting damage as soon as it is discovered.
This will help in filling out the claim forms later.
2. As soon as damage is discovered or suspected, notify
the carrier that delivered the shipment.
3. Arrange for the carrier's representative to examine the
damage.
4. Fill out all carrier claims forms and have the examining
carrier sign and date each form.
GENERAL
Installation of the kettle must be accomplished by qualified
installation personnel working to all applicable local and
national codes. Improper installation of product could
cause injury or damage.
This equipment is built to comply with applicable standards
for manufacturers. Included among those approval
agencies are: UL, A.G.A., NSF, ASME/N.Bd., CSA, CGA,
ETL, and others. Many local codes exist, and it is the
responsibility of the owner/installer to comply with these
codes.
Observe all clearance requirements to provide proper
make-up air flow. Do not obstruct the flow of combustion
and ventilation air. Check rating plate to ensure that kettle
has been equipped to operate with the type of gas
available at the installation.
Dimensions and clearance requirements are shown on the
Specification Sheet.
INSTALLATION
CLEARANCE REQUIREMENTS
This unit must be installed in accordance with the
clearances shown on the rating label which is adhered to
the unit.
Manual Tilt
Power Tilt
*Allow 3.5" at rear for combustable walls.
FOR YOUR SAFETY. Keep the appliance area free and
clear of combustible materials.
INSTALLATION
1. Position the unit in it's permanent location, and level the
unit by turning the adjustable feet.
2. Once positioned and leveled, permanently secure the
unit's flanged feet to the floor using 5/16" lag bolts and
floor anchors (supplied by the installer). Three bolts are
required to secure each of the flanged feet.
3. Seal joints of flanged feet with a silicone sealant.
GAS
ENSURE THE GAS SUPPLY MATCHES THE KETTLE'S
REQUIREMENTS AS STATED ON THE RATING PLATE.
Installation must conform, with local codes or in the
absence of local codes, with the National Fuel Gas Code
ANSI Z223.1/NFPA 54, or the Natural Gas and Propane
Installation Code, CSA B149.1.
The appliance and its individual shut-off valve must be
disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in
excess of 1/2 psi (3.45 kPa).
The appliance must be isolated from the gas supply piping
system by closing its individual manual shut-off valve
during any pressure testing of the gas supply piping
system at test pressures equal to or less than 1/2 psi (3.45
kPa).
It is recommended that a sediment trap (drip leg) be
installed in the gas supply line. If the gas pressure exceeds
14" water column, a pressure regulator must be installed, to
provide a maximum of 14" water column gas pressure to
the gas control valve.
Connect the gas line to the manual valve located at the
rear of the control box.
Use a gas pipe joint compound which is resistant to L.P.
gas. Test all pipe joints for leaks with soap and water
solution. Ensure that the gas pressure regulator is set for
the manifold pressure indicated on the gas rating plate.
RIGHT LEFT REAR
4" 0
1" 0
0*
0*