Technical Data; Mounting Instruction; Important - Nederman 865 Manuel D'instruction

GB
Foreword
To guarantee a correct function and a minimal service,
it is important to read and understand the information
in this instruction manual.
The product is designed to meet the requirements
of the relevant EC directives. To maintain this status
all installation, repair and maintenance work must be
carried out by qualified personnel using only original
spare parts. Contact your nearest authorised dealer
or AB Ph. Nederman & Co. for advice on technical
service or if you require spare parts.

Technical data

Weight:
without hose: 37 kg (82 lbs)
with hose and nozzle: 47 – 62 kg (104 – 137 lbs)
Recommended mounting height
with hose NFC-3: maximum 5 m (17 ft)
with hose NR-B: maximum 6 m (20 ft)
Duct connection
Ø 200 mm (8 in)
Recommended airflow
trucks and buses:
800 – 2500 m /h (500 – 1500 cfm)
3
Ambient temperature
-10 °C to +50 °C (15 °F to 120 °F)
Recommended hoses
Hose temperature resistance
hose NR-B: 150 °C (300 °F) continuously
hose NFC-3: 300 °C (570 °F) continuously
Noise level
measured according to ISO 11201. < 70 dB(A).
Material recycling
reels without hose: 100 weight-%

Mounting instruction

See pictures, page 2.
1. Make sure that the surface, on which to
mount the reel, is level. Drill 4 holes, using the
hole template which comes in the package.
2. Fit the mounting brackets in such a way that will
make the reel hanging horizontally. Ensure that suita-
ble fixing bolts are used considering the ceiling
or wall construction material. The bolts must each
stand a tractive force of minimum 6500 N.
3. Use approved lifting equipment to lift the reel. Fas-
ten the reel in the brackets.
4. Fit the hose stop on the hose in such position
that the nozzle stops in a desired position when the
hose is recoiled.
8
EXHAUST HOSE REEL
Safety lock
WARNING !
Risk of personal injury.
The reel is equipped with a safety lock
which should be used during service or
repair work on the reel, for example when moun-
ting or changing the hose.
NB! When changing the spring the spring power
must be completely neutralized (instruction is
delivered together with the spare part spring)
Mounting the hose
See pictures, page 3. When the reel has been moun-
ted on wall or ceiling, the hose is mounted
in the following way (concerning reels delivered wit-
hout hose only):
1. Fasten the hose with a hose clip on the
connecting piece.
2. Pull out the safety lock.
3. Wind all the hose on, by turning the drum in the
direction of the arrow. Ensure that the hose only forms
one layer on the drum.
4. Tension the spring. See "Ajustment of spring ten-
sion" page 9.
5. Fit the hose stop on the hose in such position
that the nozzle stops in a desired position when
the hose is recoiled.
6. Fit the nozzle
Ratchet device
See pictures, page 3. The reel is fitted with a ratchet
device which lock's the hose in the desired position.
The ratchet is released when the hose is pulled out
slightly further and the hose is then automatically
recoiled.
The ratchet is factory set for ceiling mounting of the
reel (position A). When mounting the reel on wall,
the ratchet must be moved from position A to B.
N.B. The ratchet must, after it has been mounted,
point towards the centre of the reel.

IMPORTANT!

See picture C, page 3. If the hose is pulled out too far,
the ratchet could unfortunately become permanently
locked. It may be released by the following procedure.
1. Take a steady grip in the drum end plate and turn
a little in the outdraw direction until the ratchet is dis-
connected.
2. Holding the end plate and hose at the same time,
then slowly release until the hose has been recoiled.
3. Fit the ratchet in the other mounting position.
See picture, page 3