Transport And Storage - Wilo COE-2-EMHIL Notice De Montage Et De Mise En Service

English
1. General
The installation and operating instruction is an
integral part of the product and must be kept
readily available near the place where the product
is installed. Strict adherence to these instructions
is a precondition for the installation and proper
use of the product. The installation and operating
instruction corresponds to the relevant version of
the product and the underlying safety standards
valid at the time of going to print.
2. Safety
This instruction contains important information
which must be followed when installing and oper-
ating. For this reason, this operating instruction
must, without fail, be read by the service techni-
cian and the responsible operator before installa-
tion and commissioning.
Both the general safety instructions in the "Safety
precautions" section and those in subsequent
sections indicated by danger symbols should be
carefully observed.
2.1 Symbols used in this operating instruction
Symbols
General symbol for danger.
Warning of electrical danger.
REMARK: ....
Signals
DANGER! Extremely dangerous situation.
The non-observance could cause death or seri-
ous injuries.
WARNING! The user may suffer from injuries
(serious). The mention «Warning» involves
that personal (serious) injuries may happen
when precautions are not observed.
ATTENTION! Damage could be caused to the
pump or installation. The mention «Attention»
is used to indicate that by ignoring the rele-
vant safety instructions, damage could be
caused to the pump or its operation.
REMARK! Useful remark for product handling. Any
possible difficulty is mentioned.
2.2 Staff training
The personnel installing the pump must have the
appropriate qualifications for this work.
2.3 Risks incurred by failure to comply with the
safety precautions
Failure to comply with the safety precautions
could result in personal injury or damage to the
pump or installation. It could also invalidate any
claims for warranty.
In particular, lack of care may lead to problems
such as:
4
• failure of important pump or machinery functions,
• failure of the maintenance and repairing process
recommended,
• danger to persons due to electrical, mechanical
and bacteriological influences,
• material damages.
2.4 Safety precautions for the operator
Existing regulations for the prevention of acci-
dents must be followed.
Dangers caused by electrical energy are to be
excluded. Local or general rules issued by the
IEC, VDE, etc. as well as the local electricity sup-
ply companies are to be observed.
2.5 Safety information for inspection and assembly
The user must ensure that all inspection and
installation works are carried out by authorised
and qualified specialists who have carefully stud-
ied these instructions.
Works on the pump or installation should only be
carried out when the machine has been brought
to a standstill.
2.6 Unauthorized modification and manufacture of
spare parts
Alterations to the pump or installation may only
be carried out with prior manufacturer's consent.
The use of original spare parts and accessories
authorized by the manufacturer will ensure safe-
ty. The use of any other parts may invalidate
claims invoking the liability of WILO for any con-
sequences.
2.7 Unauthorized operating methods
The operating safety of the pump or installation
supplied can only be guaranteed if it is used in
accordance with chapter 4 of the operating
instruction. The limiting values given in the cata-
logue or data sheet must neither be exceeded
nor allowed to fall below those specified.

3. Transport and storage

The booster is supplied on a pallet and is film-
wrapped to protect it against moisture and dust.
• The equipment must be transported by means of
authorised load devices.
• Transport straps must be placed round the steel
base frame.
• The manifolds will not withstand loads and
should not be used to secure loads in transit.
ATTENTION! Loading the pipes in transit can
result in leaks.
When the product is delivered, check it for any
damage in transit. If any defect is found, inform
the delivery company (forwarding agent).
ATTENTION!
If the product is installed later on, store it in a dry
place. Protect it from impacts and any outside
influences (moisture, frost, etc.).
Handle the product with care.
WILO SE 04/2013