Instructions For Assembly - Kettler Giro LTD HT1008-400 Instructions De Montage

The location for the device must be selected
•
EN
such that a sufficient and safe distance from any
obstacles is maintained. In the immediate vici-
nity of the main operational directions, nothing
else should be placed. There should be at least
one meter of free space surrounding the exer-
cise space. – Make sure that no one, other than
the person who is training, is in the device space
when the device is in motion.
Always observe the general safety rules and pre-
•
cautions for working with electrical equipment.
Do not use a multiple power socket for the run-
•
ning belt. If an extension cable is being used, en-
sure that it complies with the VDE regulations.
Unplug the power cord of the device from the so-
•
cket if not used for a longer period.
The product is not suitable for use by persons
•
weighing over 130 kg.
Nobody may be in the moving range of a training
•
person during training
This exercise machine may only be used for
•
exercises indicated in the training instructions.
This training device has to be set up on a ho-
•
rizontal surface under all circumstances. Place
rubber or straw mats under it to deaden any noi-
se or impacts. Only for appliances with weights.
Avoid powerful oscillations of the dumbbells!
When mounting the product please take the re-
•

INSTRUCTIONS FOR ASSEMBLY

྇
RISK! Ensure that your working area is free of possible
sources of danger, for example don't leave any tools lying
around. Always dispose packaging material in such a way
that it may not cause any danger. There is always a risk of
suffocation if children play with plastic bags!
྇
WARNING! Please note that there is always a danger of in-
jury when working with tools or doing manual work. There-
fore please be careful when assembling this machine.
• Ensure that you have received all the parts required (see
check list) and that they are undamaged. Should you have
any cause for complaint, please contact your KETTLER
dealer.
• Before assembling the equipment, study the drawings ca-
refully and carry out the operations in the order shown by
the diagrams. The correct sequence is given in capital let-
ters.
• The equipment must be assembled with due care by an
HANDLING THE EQUIPMENT
• Before using the equipment for exercise, check carefully to
ensure that it has been correctly assembled.
• It is not recommended to use or store the apparatus in
a damp room as this may cause it to rust. Please ensure
8
commended torque information into account (
= xx Nm).
The actual human performance can differ from
•
the mechanical performance shown.
Please note: for devices without a freewheel, the
•
moving parts cannot immediately be stopped.
The symbol identifies devices in Protection
•
Class I.
The symbol identifies devices in Protection
•
Class II.
The symbol identifies devices in Protection
•
Class III.
The training device corresponds with DIN EN
•
ISO 20957-1:2014/DIN EN ISO 20957-5:2017,
class HB. Notice that class B and class C crank
training equipment are not suitable for high ac-
curacy purposes.
The device may only be used with the power
•
supply units delivered.
HRC Training Program
྇ WARNING! If you lose the pulse signal, the per-
formance of the device will remain constant for
approx. 60 seconds and is then slowly adjusted
downwards. Please check your pulse measuring
system (ear clip, hand pulse or chest belt) so
that the pulse signal of the electronics can be
entered again.
adult person. If in doubt call upon the help of a second per-
son, if possible technically talented.
• The fastening material required for each assembly step
is shown in the diagram inset. Use the fastening material
exactly as instructed.
• Bolt all the parts together loosely at first, and check that
they have been assembled correctly. Tighten the locknuts
by hand until resistance is felt, then use spanner to finally
tighten nuts completely against resistance (locking device).
Then check that all screw connections have been tightened
firmly. Attention: once locknuts have been unscrewed they
no longer function correctly (the locking device is destroy-
ed), and must be replaced.
• For technical reasons, we reserve the right to carry out
preliminary assembly work (e.g. addition of tubing plugs).
• For a comfortable training position please adjust the hand-
lebar andsaddle position to your body height.
that no part of the machine comes in contact with liquids
(drinks, perspiration etc.). This may cause corrosion.
• The machine is designed for use by adults and children
should not be allowed to play with it. Children at play be-