For Your Safety; Instructions For Assembly; List Of Spare Parts - Kettler Golf E Mode D'emploi

GB Assembly Instructions
Before assembling or using the exercise cycle , please read the following instructions carefully. They contain important
information for use and maintenance of the equipment as well as for your personal safety. Keep these instructions in a
safe place for maintenance purposes or for ordering spare parts.

For Your Safety

Exercise should be used only for its intended purpose, i.e. for physical
exercise by adult persons.
Any other use of the equipment is prohibited and may be dangerous. The
manufacturer cannot be held liable for damage or injury caused by
improper use of the equipment.
Exercise has been designed in accordance with the latest standards of safety.
Any features which may have been a possible cause of injury have been
avoided or made as safe as possible.
The unit requires a power supply of 220-230 V/50 Hz. It should be con-
nected only to a safety socket with a single 10-A fuse. Before commis-
sioning the appliance pay attention to the fact that the correct plug-in power
supply unit (observe marking) has been connected properly. Do not
under any circumstances carry out electrical repairs or alterations yourself.
Always ensure that such work is done by a properly qualified electrician.
Important: disconnect the apparatus from the mains before doing repair,
maintenance or cleaning work.
Incorrect repairs and structural modifications (e.g. removal or replacement
of original parts) may endanger the safety of the user.
Handling the equipment
Before using the equipment for exercise, check carefully to ensure that it
has been correctly assembled.
It is not recommended to use or store the apparatus in a damp room as
this may cause it to rust. Please ensure that no part of the machine
comes in contact with liquids (drinks, perspiration etc.). This may cause
corrosion.
The Hometrainer is designed for use by adults and children should not
be allowed to play with it. Children at play behave unpredictably and
dangerous situations may occur for which the manufacturer cannot be
held liable. If, in spite of this, children are allowed to use the equipment,
ensure that they are instructed in its proper use and supervised accor-
dingly.
The Ergometer complies fully with DIN EN 957 - 1/5, class A. It is therefore
suitable for therapeutic purposes.
On principle, the equipment does not require any special maintenance.
All bearings are pre-lubricated (further lubrication is not required) and

Instructions for Assembly

Ensure that you have received all the parts required (see check list) and
that they are undamaged. Should you have any cause for complaint, please
contact your KETTLER dealer.
Before assembling the equipment, study the drawings carefully and carry
out the operations in the order shown by the diagrams. The correct
sequence is given in capital letters.
The equipment must be assembled with due care by an adult person. If
in doubt call upon the help of a second person, if possible technically
talented.
Please note that there is always a danger of injury when working with
tools or doing manual work. Therefore please be careful when assem-
bling this machine.
Ensure that your working area is free of possible sources of danger, for
example don't leave any tools lying around. Always dispose packaging
material in such a way that it may not cause any danger. There is
always a risk of suffocation if children play with plastic bags!

List of spare parts

When ordering spare parts, always state the full article number, spare-part number,
the quantity required and the inspection number stamped on the back.
Example order: Art. no. 7961 - 600 / spare-part no. 10100030/ 2 pieces /
inspection no......
Important: spare part prices do not include fastening material; if fastening material
(bolts, nuts, washers etc.) is required, this should be clearly stated on the order
by adding the words „with fastening material".
All manuals and user guides at all-guides.com
Damaged components may endanger your safety or reduce the lifetime
of the equipment. For this reason, worn or damaged parts should be
replaced immediately and the equipment taken out of use until this has
been done. Use only original KETTLER spare parts.
In case of enquiry, please contact your KETTLER dealer.
If the equipment is in regular use, check all its components thoroughly
every 1–2 months. Pay particular attention to the tightness of bolts and
nuts.This applies especially to the securing bolts for saddle and handelbars.
The brake tension should also be checked at regular intervals and
adjusted as necessary.This applies especially to the securing bolts for saddle
and handelbars.
Instruct persons using the equipment (in particular children) on possible
sources of danger during exercising.
Before beginning your program of exercise, consult your doctor to ensure
that you are fit enough to use the equipment. Base your program of exercise
on the advice given by your doctor. Incorrect or excessive exercise may
damage your health.
require little maintenance.
A slight production of noise at the bearing of the centrifugal mass is due
to the construction and has no negative effect upon operation. Possibly
occurring noise during reverse pedalling result from engineering and are
absolutely safe.
Do not use corrosive or abrasive materials to clean the equipment.
Ensure that such materials are not allowed to pollute the environment.
The exercise cycle has a brake system, which requires little maintenance
and does not require any adjusting work.
The Ergometer works independent of revolutions per minute.
Please ensure that liquids or perspiration never enter the machine or the
electronics.
Before use, always check all screws and plug-in connections as well as
respective safety devices fit correctly.
The fastening material required for each assembly step is shown in the
diagram inset. Use the fastening material exactly as instructed. The
required tools are supplied with the equipment
Bolt all the parts together loosely at first, and check that they have been
assembled correctly. Tighten the locknuts by hand until resistance is felt,
then use spanner to finally tighten nuts completely against resistance
(locking device). Then check that all screw connections have been tigh-
tened firmly. Attention: once locknuts have been unscrewed they no
longer function correctly (the locking device is destroyed), and must be
replaced.
To pull off the pedal arms screw a bolt M 12 (it's not supplied by the
manufacturer) into the threaded opening after removing the protective cap
and bolt.
For technical reasons, we reserve the right to carry out preliminary
assembly work (e.g. addition of tubing plugs).
Please keep original packaging of this article, so that it may be used for
transport at a later date, if necessary.
KETTLER (GB) Ltd. · Merse Road · North Moons Moat · Redditch, Worcestershire
B98 9HL · Great Britain
KETTLER International Inc. · 1355, P. B. 2747 · Virginia Beach · VA 23450 USA
www.kettler.net
.