Optional Accessories - Makita DTP131 Manuel D'instructions

NOTE:
• This tool employs an electronic clutch. The tool stops
automatically when the clutch cuts in. To keep operat-
ing, release the switch trigger once.
• When driving wood screws, predrill pilot holes to make
driving easier and to prevent splitting of the workpiece.
See the chart.
Nominal diameter of wood
screw (mm)
3.1
3.5
3.8
4.5
4.8
5.1
5.5
5.8
6.1
006421
NOTE:
• See the following chart for the relation between the
number of torque setting and fastening torque rate.
The fastening torque rate will be different depends on
materials. Make a test fastening to get the desired
torque before operation.
Number Fastening torque rate
on LED
Low (1)
Display
Approx. 2.5 N•m
1
(Approx. 25.5 kgf. cm)
Approx. 4.6 N•m
3
(Approx. 46.9 kgf. cm)
Approx. 8.1 N•m
5
(Approx. 82.6 kgf. cm)
Approx. 10.0 N•m
7 (Approx. 102.0 kgf.
cm)
Approx. 11.5 N•m
9
(Approx. 117.3 kgf. cm)
012276
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and the bat-
tery cartridge is removed before attempting to perform
inspection or maintenance except for the following trou-
bleshooting related to the light.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
Recommended size of
pilot hole (mm)
2.0 – 2.2
2.2 – 2.5
2.5 – 2.8
2.9 – 3.2
3.1 – 3.4
3.3 – 3.6
3.7 – 3.9
4.0 – 4.2
4.2 – 4.4
High (2)
Approx. 1.1 N•m
(Approx. 11.2 kgf. cm)
Approx. 2.0 N•m
(Approx. 20.4 kgf. cm)
Approx. 3.0 N•m
(Approx. 30.6 kgf. cm)
Approx. 4.0 N•m
(Approx. 40.8 kgf. cm)
Approx. 5.8 N•m
(Approx. 59.1 kgf. cm)

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Screw bits
• Hook
• Plastic carrying case
• Various type of Makita genuine batteries and chargers
NOTE:
• Some items in the list may be included in the tool pack-
age as standard accessories. They may differ from
country to country.
Noise
The typical A-weighted noise level determined according
to EN60745:
Model DTP131
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Model DTP141
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Model DTP131
Work mode: impact drilling into concrete
Vibration emission (a
Uncertainty (K): 1.5 m/s
Work mode: impact tightening of fasteners of the
maximum capacity of the tool
Vibration emission (a
Uncertainty (K): 2 m/s
Work mode: drilling into metal
Vibration emission (
Uncertainty (K): 1.5 m/s
Model DTP141
Work mode: impact drilling into concrete
Vibration emission (a
Uncertainty (K): 1.5 m/s
Work mode: impact tightening of fasteners of the
maximum capacity of the tool
Vibration emission (a
Uncertainty (K): 1.5 m/s
Work mode: drilling into metal
Vibration emission (
Uncertainty (K): 1.5 m/s
ENG905-1
): 85 dB (A)
pA
): 96 dB (A)
WA
): 85 dB (A)
pA
): 96 dB (A)
WA
ENG900-1
2
): 13 m/s
h , ID
2
2
): 8.5 m/s
h
2
2
or less
): 2.5 m/s
a
h, D
2
2
): 13 m/s
h ID
,
2
2
): 10.5 m/s
h
2
2
or less
): 2.5 m/s
a
h, D
2
11