Safety Instructions; Machine Overview - Festool MFT/ KAPEX Notice D'utilisation D'origine

Table multifonctions
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 8
MFT
GB
Original operating manual
1
Symbols
Symbol Significance
Warning of general danger
Read operating instructions and safety
notices!
Do not dispose of with domestic waste.
Tip or advice
Handling instruction
2

Safety instructions

WARNING Read all safety warnings and all
instructions provided with the working
stand and the power tool to be mounted. Failure to
follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future ref-
erence.
The term "power tool" in the warnings refers to
your mains-operated (corded) power tool or bat-
tery-operated (cordless) power tool.
– Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments or changing accesso-
ries. Accidental starting of the power tool is a
cause of some accidents.
– Properly assemble the working stand before
mounting the tool. Proper assembly is important
to prevent risk of collapse.
– Securely fasten the power tool to the working
stand before use. Power tool shifting on the
working stand can cause loss of control.
– Place the working stand on a solid, flat and level
surface. When the working stand can shift or
rock, the power tool or workpiece cannot be
steadily and safely controlled.
– Do not overload the working stand or use as lad-
der or scaffolding. Overloading or standing on
the working stand causes the stand to be "top-
heavy" and likely to tip over.
– Observe the operating instructions of the elec-
tric power tool being installed. Non-compliance
with the safety instructions and the maximum
workpiece dimensions make the tool unsafe and
may lead to accidents.
6
3
Intended use
The multifunction table MFT / K A P E X is in-
tended for mounting the KAPEX KS 120/KS 88.
The multifunction table MFT/3 C O N T U R O is
intended for mounting the edge bander KA 65.
The user is liable for improper or non-in-
tended use.
4
Technical data
Multifunction
table
Table dimensions
869x581 mm
(Width x Length)
(34.2 x 22.9")
Tabletop height
- with foldaway
legs
- without foldaway
legs
Weight
5

Machine overview

[1A]
MFT / K A P E X
with
[1-1]
Knobs
[1-2]
Corner feet
[1-3]
Rotatable end cap
[1B]
MFT/3 C O N T U R O
with
[1-1]
Knobs
[1-2]
Corner feet
[1-3]
Rotatable end cap
[1-4]
Cross brace MFT 3-QT
[1-5]
Adapter plate AP-KA 65
The specified illustrations appear at the beginning
of the Operating Instructions.
6
Setup
Ensure that the floor around the machine is
level, in good condition and free of loose ob-
jects (e.g. chips and offcuts).
Screw on knobs [1-1] as far as stop.
Unfold the foldaway legs and tighten the knobs
on the joints to secure.
Unevenness in the stand area can be offset by
turning the end cap [1-3].
MFT/
MFT/3
K A P E X
C O N T U R O
1157x773 mm
(45.6 x 30.4")
790 mm
900 mm
(31.1")
(35.4")
180 mm
180 mm
(7.1")
(7.1")
18 kg
24.6 kg
(39.7 lbs)
(54.2 lbs)

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Mft/3 conturo

Table des Matières