Troubleshooting - Maytag W10345638A Guide D'utilisation

Cuisinière deux fours avec table de cuisson à revêtement lisse
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
Nothing will operate
Is the power supply cord unplugged?
Plug into a grounded outlet.
Has a household fuse blown, or has a circuit breaker
tripped?
Replace the fuse or reset the circuit breaker. If the problem
continues, call an electrician.
Cooktop will not operate
Is the control knob set correctly?
Push in knob before turning to a setting.
Is the Cooktop Control Lock set? See "Control Lock"
section.
Excessive heat around cookware on cooktop
Is the cookware the proper size?
Use cookware about the same size as the surface cooking
area, element or surface burner. Cookware should not extend
more than ½" (1.3 cm) outside the cooking area.
Hot Surface indicator light stays on
Does the Hot Surface indicator light stay on after control
knob(s) have been turned off?
See "Cooktop Controls" section.
Cooktop cooking results not what expected
Is the proper cookware being used?
See "Cookware" section.
Is the control knob set to the proper heat level?
See "Cooktop Controls" section.
Is the range level?
Level the range. See the Installation Instructions.
Oven will not operate
Is the electronic oven control set correctly?
See "Electronic Oven Controls" section.
On some models, is the oven control lockout set?
See "Control Lockout" section.
Oven temperature too high or too low
Does the oven temperature calibration need adjustment?
See "Oven Temperature Control" section.
On some models, does the cooling fan run during BAKE,
BROIL or CLEAN?
It is normal for the fan to automatically run when the oven is
in use. This helps cool the electronic control.

TROUBLESHOOTING

Oven indicator lights flash
Do the oven indicator lights flash?
See the "Display" and/or the "Oven Lights" section. If the
indicator light(s) keeps flashing, call for service. See
"Assistance or Service" section.
Display shows messages
Is the display showing a flashing time?
There has been a power failure. Clear the display. See
"Display(s)" section. On some models, reset the clock, if
needed. See "Clock" section.
Is the display showing a letter followed by a number?
Depending on your model, press OFF/CANCEL, OFF or
CANCEL/OFF to clear the display. See "Display(s)" section. If
it reappears, call for service. See "Assistance or Service"
section.
Self-Cleaning cycle will not operate
Is the oven door open?
Close the oven door all the way.
Has the function been entered?
See "Self-Cleaning Cycle" section.
On some models, has a delay start Self-Clean cycle been
set?
See "Self-Cleaning Cycle" section.
Oven cooking results not what expected
Is the range level?
Level the range. See the Installation Instructions.
Is the proper temperature set?
Double-check the recipe in a reliable cookbook.
Is the proper oven temperature calibration set?
See "Oven Temperature Control" section.
Was the oven preheated?
See "Baking" section.
Is the proper bakeware being used?
See "Bakeware" section.
Are the racks positioned properly?
See "Positioning Racks and Bakeware" section.
Is there proper air circulation around bakeware?
See "Positioning Racks and Bakeware" section.
Is the batter evenly distributed in the pan?
Check that batter is level in the pan.
Is the proper length of time being used?
Adjust cooking time.
Has the oven door been opened while cooking?
Oven peeking releases oven heat and can result in longer
cooking times.
Are baked items too brown on the bottom?
Move rack to higher position in the oven.
Are pie crust edges browning early?
Use aluminum foil to cover the edge of the crust and/or
reduce baking temperature.
23

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Met8885xsMet8720dsMet8720dh

Table des Matières