PRESIDENT RONALD 10/12 M Manuel D'utilisation page 24

7) DW SETTING
Press for 2 seconds F (7) key to access
1. Use UP/DN keys (11) on the microphone or turn PUSH knob (5) to
function.
2. Press PUSH knob (5). The dual watch channel blinks on LCD.
3. Use UP/DN keys (11) on the microphone or turn PUSH knob (5) to
dual watch channel of your choice.
4. New press PUSH knob (5) permits to
channel. The channel stops blinking. The second parameter, the frequency
band, blinks.
5. Use UP/DN keys (11) on the microphone or turn PUSH knob (5) to
frequency band in segments:
page 25).
6. New press PUSH knob (5) permits to
band stops blinking. The third parameter, the mode, blinks.
7. Use UP/DN keys (11) on the microphone or turn PUSH knob (5) to
mode AM or FM .
8. New press PUSH knob (5) permits to
stops blinking. a) Return to point 1 to
PTT switch (10) to validate and exit
9. If no key is pressed, the unit exits
press on F (7) key.
Default Dual watch channel is 9.
See § DW (Dual Watch) page 20.
8) SCAN TYPE
Press for 2 seconds F (7) key to access
1. Use UP/DN keys (11) on the microphone or turn PUSH knob (5) to
function.
2. Press PUSH knob (5). The current setting blinks on LCD.
3. Use UP/DN keys (11) on the microphone or turn PUSH knob (5) to
type of SCAN. SQ Squelch or tI time.
4. New press PUSH knob (5) permits to
blinking. a) Return to point 1 to
switch (10) to validate and exit
5. If no key is pressed, the unit exits
press on F (7) key.
sq: scanning stops when busy channel is founded and doesn't restart as long
as this channel remains active.
tI: scanning stops when busy channel is founded and return to scan after
5 seconds even if the channel remains active.
Default Scan type is Sq.
to MENU. is displayed.
validate
the choice of the dual watch
(see BAND NAME
validate
the choice of the band. The
validate the chosen mode. The mode
select another function to set or b) Press
MENU.
after 10 seconds or by a new long
MENU
to MENU. is displayed.
validate the choice. The setting stops
select another function to set or b) Press PTT
MENU.
MENU after 10 seconds or by a new long
See § SCAN page 20.
9) SWR
select the
Press for 2 seconds F (7) key to
1. Use UP/DN keys (11) on the microphone or turn PUSH knob (5) to
function.
select
the
2. Press PUSH knob (5). The channel, the band and the mode blink on LCD.
3. Press PTT switch (10), the SWR value is displayed. In this function, as in the RF
POWER function, a press on PTT switch (10) key
4. If no key is pressed, the unit exits
press on F (7) key.
select
the
See § HOW TO ADJUST SWR page 19.
10) SPAN
Press for 2 seconds F (7) key to
select the
1. Use UP/DN keys (11) on the microphone or turn PUSH knob (5) to
function.
2. Press PUSH knob (5). The current setting blinks on LCD.
3. Use UP/DN keys (11) on the microphone or turn PUSH knob (5) to
deactivate OF the SPAN function.
4. New press PUSH knob (5) key permits to
blinking on LCD. a) Return to point 1 to
Press PTT switch (10) to
5. If no key is pressed, the unit exits
press on F (7) key.
When the function is active, the frequency can be adjusted continuously. A
short press PUSH knob (5) displays a bar in one of decimals of the frequency.
1. Press repeatedly to
select
the
the microphone or turn PUSH knob (5) to
continuously with the channel and the band.
Note: the last two digits of the frequency may blink if it doesn't match exactly
select
the
the frequency of the displayed channel.
Default setting is On.
11) MIC TYPE
The PRESIDENT RONALD 10/12 M can be used with the electret microphone
as well as with the dynamic one, 6-pin PRESIDENT (see the cabling diagram
page 71).
Press for 2 seconds F (7) key to
1. Use UP/DN keys (11) on the microphone or turn PUSH knob (5) to
function.
2. Press PUSH knob (5). The current setting blinks on LCD.
24
access to MENU. is displayed.
doesn't exit
MENU after 10 seconds or by a new long
access
to MENU. is displayed.
validate the choice. The setting stops
select another function to set or b)
validate exit
and MENU.
MENU after 10 seconds or by a new long
select the desired decimal. 2. Use UP/DN keys (11) on
increase/decrease
access to MENU. is displayed.
select
the
from MENU.
select the
activate
On/
the frequency
select
the