JB Systems Light LED Quadra Beam Mode D'emploi page 5

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 6
ENGLISH
You can inverse the behavior of one or more slave units by changing the position of DIP-switch n°10 on
these slaves. Just try it and see if the effect becomes better.
3. Connect the optional CA-8 controller for more control:
The CA-8 controller can only be used in standalone or master/slave mode. Connect the
controller to the jack input of the first unit (master). Now you can control all the connected
units:
Blackout the unit
Stand by
1. Synchronous Strobe
Function
2. Sound Strobe
3. Two light Strobe
Mode
Strobe (LED OFF)
4. DMX-mode:
When the units are connected in DMX-mode, they can be controlled using the following DMX-chart:
Two DMX-modes are available: 1CH and 6CH mode:
1 channel mode:
Extremely user friendly mode: you only need 1 DMX channel to choose 1 of the 12 preprogrammed
sound chases or you can use our Effect commander to switch the unit ON/OFF (no switch pack
needed).
6 channel mode:
You can take full control of all pre-programmed functions of the effect.
 Channel 1: switch the unit on/off and select one of the 25 chases.
 Channel 2: Control for the strobe function.
 Channel 3: Control the output for the red LEDs.
 Channel 4: Control the output for the green LEDs.
 Channel 5: Control the output for the blue LEDs.
 Channel 6: Control the output for the general dimmer.
1 CHANNEL MODE
JB SYSTEMS
®
OPERATION MANUAL
Select a show
Show (LED ON)
6 CHANNEL MODE
5/40
LED QUADRA BEAM
ENGLISH
MAINTENANCE
 Make sure the area below the installation place is free from unwanted persons during servicing.
 Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
 All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
 Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
 When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
 The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
 In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.
 The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
 The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit's optics.
 Clean with a soft cloth using normal glass cleaning products.
 Always dry the parts carefully.
 Clean the external optics at least once every 30 days.
 Clean the internal optics at least every 90 days.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
SPECIFICATIONS
Mains Input:
AC 100V to 240V, 50/60Hz
Power consumption:
12 Watt
Fuse:
250V 6,3A slow blow (20mm glass)
Sound Control:
Internal microphone
DMX connections:
3pin XLR male / female
DMX channels used:
1 or 6 channels
Lamp:
256 LEDs (R96 + G96 + B64)
Size:
965 x 190 x 82cm
Weight:
6,4kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
JB SYSTEMS
®
OPERATION MANUAL
6/40
LED QUADRA BEAM

Publicité

Table des Matières
loading

Table des Matières