VINCENT SV-123 Manuel D'utilisation page 35

O O p p e e r r a a t t i i o o n n
Selecting the RDS
radio as the input
source
Selecting the
frequency band
Switching between
stereo/mono
M M O O D D E E
Selecting a radio
frequency in
search mode
Selecting a radio
station by inputting its
radio frequency
numerically
M M O O D D E E
Changing to playback
from a preset station
B B u u t t t t o o n n D D e e s s c c r r i i p p t t i i o o n n
To activate radio mode you can either press the "TUNER" button on the
I I N N P P U U T T ( ( 2 2 ) )
T T U U N N E E R R ( ( 1 1 8 8 ) ) remote control or select this input on the front panel of the appliance with the
"INPUT" knob.
This button is found on both the remote control and the front of the appliance.
This allows you to switch between the FM (VHF) and AM (MW) modes when
A A M M / / F F M M
the radio is on. VHF offers better sound quality and a greater selection of
( ( 6 6 ) ) ( ( 2 2 4 4 ) )
stations.
This button is found on both the remote control and the front of the appliance.
If a station can only be received with poor quality in stereo, there is an option
S S T T / / M M O O N N O O
of listening to it in mono mode. This can improve the sound quality.
( ( 6 6 ) ) ( ( 2 2 5 5 ) )
Switching between these two is only possible for the radio. Whilst this setting
is active, the display shows "MONO" in small letters.
T T U U N N I I N N G G
When the radio is on, use the "TUNING MODE" button on the front of the
appliance or on the remote control to select one of the two following options
from the three possible settings (function of the Tuning/Preset buttons):
( ( 6 6 ) ) ( ( 2 2 6 6 ) )
• MANUAL The display briefly shows "MANUAL". If this mode is
selected you can change the radio frequency up or down with the
T T U U N N I I N N G G
" TUNING PRESET " buttons on the front of the appliance or
P P R R E E S S E E T T
" TUN/PRE " on the remote control step by step (in steps
( ( 6 6 ) )
of 0.05 MHz for FM and 9 kHz for AM).
• AUTOSCAN The text "AUTOSCAN" can be seen briefly on the display.
In this mode the selected frequency band is automatically searched up or
T T U U N N / / P P R R E E
down (automatic frequency search) when " TUN/PRE " is pressed, and the
( ( 2 2 3 3 ) )
tuner stops at the next frequency with sufficiently strong reception.
D D I I R R E E C C T T
To input a known station frequency directly, you can proceed as follows
( ( 6 6 ) ) ( ( 2 2 0 0 ) )
(the keys are found both on the appliance and the remote control):
Press the "DIRECT" button. The receiver waits for an entry using the
N N u u m m e e r r i i c c a a l l
numerical keys in the next few seconds. In FM mode, 5 numbers need to
k k e e y y s s
be entered, two of which come after the decimal point of the frequency
( ( 6 6 ) ) ( ( 1 1 9 9 ) )
in MHz. If an invalid frequency is entered, the appliance corrects this to
the nearest valid frequency.
T T U U N N I I N N G G
You are able to store up to 30 radio frequencies for each of the frequency
bands (FM, AM) and select them using their positions in the memory.
If stations have already been stored, one of them can now be selected by
( ( 6 6 ) ) ( ( 2 2 6 6 ) )
entering the position in the memory with the numerical keys. To search through
all the stations stored, the "TUNING MODE" button on the front of the appli-
T T U U N N I I N N G G
ance or on the remote control can be used to select the third of the three
P P R R E E S S E E T T
possible settings
( ( 6 6 ) )
• PRESET (search through all stations stored). "PRESET" can be seen briefly
on the display. Using the " TUNING PRESET " buttons on the front of the
T T U U N N / / P P R R E E
appliance or the " TUN/PRE " buttons on the remote control, it is now
( ( 2 2 3 3 ) )
possible to go through all the positions already stored.
TUNER
Vincent
35