Control Unit - JB Systems usb 2.2 Mode D'emploi

ENGLISH
 In the event of serious operating problems, stop using the appliance and contact your dealer immediately.
 Please use the original packing when the device is to be transported.
 Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
INSTALLATION GUIDELINES:
 Placing and using the unit for long periods near heat-generating sources such as amplifiers, spotlights,
etc. will affect its performance and may even damage the unit.
 Take care to minimize shocks and vibrations during transport.
 When installed in a booth or flight case, please make sure to have good ventilation to improve heat
evacuation of the unit.
 To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when
bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full
performance.
 Choose the place where you put your installation very carefully. Avoid presence of heat sources. Avoid
places with vibrations or places that are dusty and humid.
 The player will work normally when installed on a surface with max. 15° inclination.
 Be very careful while handling CDs, do not touch them with wet or dirty hands.
 Discs that are dirty must be cleaned with special designed cloth and cleaning products.
 Do not use CDs that are badly damaged (scratched or deformed) they can damage your appliance.
 To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
 In order to prevent electric shock, do not open the top cover. If a problem occurs, contact your dealer.
 Do not place metal objects or spill liquid inside the Player. Electric shock or malfunction may result.
 This Player uses the semiconductor laser. To allow you to enjoy music at a stable operation, it is
recommended to use this in a room of 5°C – 35°C.
 The compact disc player should not be adjusted or repaired by anyone except properly qualified service
personnel.
 This unit may cause interference to radio and television reception.
CLEANING THE PLAYER:
Clean by wiping with a polished cloth slightly dipped with water. Avoid getting water inside the unit. Do not
use volatile liquids such as benzene or thinner which will damage the unit.
CONNECTIONS
 Connect the mini-DIN8 cable between the control unit and the main unit (CD loader)
 Use the supplied cinch cables to connect the audio outputs of the Player with the CD or line inputs on your
mixing unit.
 Connect the mains cable.
CONTROLS AND FUNCTIONS (MAIN UNIT)
1. POWER ON/OFF switch: switches the Player on and off.
2. DISC TRAY: Use the OPEN/CLOSE buttons to open disc tray and put the CD in place.
3. OPEN/CLOSE button: press this button to open and close the disc tray. These buttons are disabled
during playback. If the tray is not closed after 60sec. It will close automatically to prevent damage.
4. USB 1 connection: this is the first (type-A) USB-connection, used to connect any USB mass storage
device that was formatted in FAT or FAT32. By default this input is used to connect an occasional USB-
drive like USB-sticks etc.
JB SYSTEMS
®
OPERATION MANUAL
3/83
ENGLISH
5. USB 2 connection: this is the second (type-A) USB-connection, used to connect any USB mass storage
device that was formatted in FAT or FAT32. By default this input is used to connect a hard disk.
6. CONTROL connector: connect this connector to the control unit, using the supplied mini-DIN8 cable.
7. AUDIO outputs: Output for the audio signals from the player. Use the supplied cinch/cinch cable to
connect this output to a CD/line input of your mixing unit.
8. MAINS input: connect the player to the AC mains, using the supplied power-cord.

CONTROL UNIT

1. TACTILE JOG-WHEEL: The jog-wheel on this player has 2 parts:
 Tactile center part: to match the vinyl feel as close as possible and largely improve scratch
performance. With the
Check the description of the JOG MODE button (2) for more information.
 Outer ring: rubber coated part of the jog wheel which is not touch sensitive. Regardless of the
selected wheel mode the outer ring can be always be used for pitch bending
2. JOG MODE button: toggles between 2 different modes for the tactile jog-wheel. The tactile center part
and outer ring behave differently:
 VINYL-mode: used for scratching of any CD or MP3 file.
USB2.2 JB SYSTEMS
JOG MODE button (2) you can change the behavior of this central part.
 Tactile center part: During playback, the music stops immediately when you touch the jog-
wheel: playback speed and direction are now fully controlled by the movements of your hand.
In pause mode you can easily set a new cue point.
 Outer ring: During playback you can use the outer ring for pitch bending to synchronize the
beats of 2 tracks. In pause mode you will hear the typical very small loops that give you the
possibility to set a cue point with 1frame (1/75seconds) accuracy.
4/83
®
OPERATION MANUAL
USB2.2