Briteq LED COLOR BANK Mode D'emploi page 5

ENGLISH
Led Display
Display on: display is always on.
Display off: display is off when not used.
 Press the MENU button until the display shows
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select
 Once the mode is selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Color Mode
to Used to select one of the preprogrammed colors .
Used to create your own color manually
 Press the MENU button until
is showing on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select
 Once the right color mode blinks on the display, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
 When you have selected the manual mode
between 0 and 255 for each of the RGB colors. Use the up-down buttons to change the value. Use the
ENTER button to go to the next RGB color.
Display Inversion
 Press the MENU button until
is blinking on the display. (normal display)
 Use the ENTER button to change to the mode
stored after 8 seconds. Or press the ENTER button again return to the mode
To go back to the functions press the MENU button.
ELECTRICAL INSTALLATION + ADDRESSING
Important: The electrical installation should be carried out by qualified personal only,
according to the regulations for electrical and mechanical safety in your country.
Electrical installation for 1 standalone unit:
 Just insert the mains cable. The unit starts working immediately in stand-alone mode.
Remark1: You can connect a CA-8 remote controller to the unit if you want to have more control. Refer to
"how to operate the unit" to learn how to do this.
Remark2: if there's no output, please make sure to set the unit in master mode (see previouschapter)
Electrical installation for two or more units in master/slave:
 Daisy chain the units together using good quality balanced microphone cables. Put the first unit of the
chain in master mode, the rest must be set to slave mode. See the previous chapter for more
information.
 Make sure that all units are connected to the mains.
 Done!
Remark: You can connect a CA-8 remote controller to the master unit if you want to have more control
over the master/slave operation
Electrical installation in DMX-mode:
 The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to
"daisy chain" your DMX controller and all the connected units with a good quality balanced cable.
 Both XLR-3pin and XLR-5pin connectors are used, however XLR-3pin is more popular because these
cables are compatible with balanced audio cables.
Pin layout XLR-3pin: Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal (+)
BRITEQ
®
OPERATION MANUAL
.
(display always on) or (display off when not used).
to , or
, you can create your own color by entering a value
(display inversion), the option will be automatically
(normal display).
5/58 LED COLOR BANK
ENGLISH
Pin layout XLR-5pin: Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal (+) ~ Pins4+5
not used.
 To prevent strange behavior of the light effects, due to interferences, you must use a
90Ω to 120Ω terminator at the end of the chain. Never use Y-splitter cables, this
simply won't work!
 Make sure that all units are connected to the mains.
 Each light effect in the chain needs to have its proper starting address so it knows
which commands from the controller it has to decode.
DMX-CONFIGURATION OF THE LED COLOR BANK:
U can control the Led Color Bank by 6, 9, 15, 27 or 24 DMX channels
BRITEQ
®
OPERATION MANUAL
6/58 LED COLOR BANK