Briteq LED COLOR BANK Mode D'emploi page 4

ENGLISH
 Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
 Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 Don't cover any ventilation openings as this may result in overheating.
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
DESCRIPTION:
1. WALL MOUNT BRACKET: used to easily fix the unit on a wall, ceiling or other flat surface.
2. REMOTE CONTROL connector: used to connect the CA-8 hand controller
3. DMX input: connect this input to the previous unit in the DMX chain or directly to the DMX-controller.
4. DMX output: connect this input to the next unit in the DMX chain
5. SENSITIVITY: to control the sensitivity of the internal microphone
6. MICROPHONE: used to control the music activated internal programs
7. MAINS CONNECTOR: connect the supplied mains cable here
8. MAINS SWITCH: to switch the LED color bank on/off
9. HANGINGBRACKET: used to fix the on truss using a standard clamp
10. MASTER LED: is lit when the unit is switched as master
11. DMX LED: is lit when the unit receives a DMX-signal
12. DISPLAY: shows the various menus and the selected functions
13. SLAVE LED: is lit when the unit is in slave mode
14. SOUND LED: blinks to the rhythm of the music while the unit is in audio mode
15. MENU BUTTON: used to browse and select the different menu items
16. DOWN BUTTON: to go back in the menu or to decrease the values shown on the display
17. UP BUTTON: to go up in the menu or to increase the values shown on the display
18. ENTER BUTTON: used to confirm your choice
HOW TO SETUP:
MAIN MENU:
 To select any of the menu options, press the MENU button up to when the required one is shown on the
display.
 Select the function with the ENTER button. The display will blink.
 Use DOWN and UP button to choose the desired menu option.
 Once the required menu option is selected, press the ENTER button to select. To go back to the functions
without any change press the MENU button or just wait 8 seconds. The menu structure is shown below.
BRITEQ
®
OPERATION MANUAL
3/58 LED COLOR BANK
ENGLISH
DMX512 Address Setting
Used to set the starting address in a DMX
setup.
 Press the MENU button until
is
shown on the display.
 Press the ENTER button, the display starts
blinking.
 Use DOWN and UP buttons to change the
DMX512 address.
 Once the correct address shows on the
display, press the ENTER button to save it.
(or automatically return to the main functions
without any change after 8 seconds)
To go back to the functions without any change
press the MENU button again.
Channel Mode
 Press the MENU button until
is
shown on the display.
 Press the ENTER button, the display starts
blinking.
 Use DOWN and UP button to select the 6
channel, 9 channel, 15 channel, 27 channel
or 24 channel mode.
 Once the mode is selected, press the
ENTER button to setup
(or automatically return to the main functions
without any change after 8 seconds)
To go back to the functions without any change
press the MENU button again.
Show Mode
Used to select one of the preprogrammed shows when used in standalone or master/slave mode.
This menu option is not available when the unit is set to slave mode
 Press the MENU button until
is showing on the display.
 Press the ENTER button, the current show starts blinking in the display.
 Use DOWN and UP buttons to select
Mode).
 Once the right show blinks on the display, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
 When you have pressed the ENTER button to confirm, a blinking S p .. will appear. Here you have to select
a chase speed between 1 and 8. Press again the ENTER button to confirm your choice, or it will return to
the main menu after 8 seconds without changing the speed of the new show.
Blackout Mode
Blackout mode: when no DMX-signal is detected, the unit goes in blackout.
No blackout mode: when no DMX-signal is detected, the unit automatically switches to master mode.
This menu option is not available when the unit is set to slave mode
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the current selection starts blinking in the display.
 Use DOWN and UP button to select Y E S (blackout) or n o (no blackout) mode.
 Once the mode is selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
BRITEQ
®
OPERATION MANUAL
(random mode), to , or
4/58 LED COLOR BANK
(Auto Fade