After Use; Technical Data - Invacare Matrx Vi Manuel D'utilisation

Cleaning the outer cover (Matrix® Vi)
1. Wipe clean the outer cover with a damp cloth.
or
2. Carefully remove the cover by unzipping the zipper found on
the rear of the cushion.
3. Close the zipper prior to laundering.
4. Machine wash at 60° C using the delicate cycle (Instructions on
label).
IMPORTANT!
Washing at higher temperatures will cause shrinkage.
Drying the outer cover
1. Hang cover from a line or bar and drip dry in a clean indoor
environment.
or
Tumble dry on a low heat setting.
IMPORTANT!
– Tumble dry setting must not exceed 40 °C.
– Do not tumble dry for longer than 10 minutes.
– Dry thoroughly before re-fitting to the foam.
Cleaning the inner cover
IMPORTANT!
Risk of damage to the product
– Do not remove the inner cover from the foam core.
1. Wipe clean the inner cover with a damp cloth.
Replacing covers
1. Carefully remove the cover by unzipping the zipper found on
the rear of the cushion.
2. Place new cover onto the foam core.
IMPORTANT!
– Ensure that the corners of the foam core are positioned
correctly into the corners of the cover.

6 After Use

6.1 Storage
IMPORTANT!
– Store cushions in a dry environment.
– Store cushions within a protective cover.
– Store items on clean, dry, off-flooring free from sharp
edges to avoid any possible damage.
– Never store other items on top of a cushion.
– Do not store cushions next to radiators or other
heating devices.
– Protect cushions from direct sunlight.
1. Refer to the storage and shipping conditions in section 7.3
Environmental Parameters, page 3 .
6.2 Re-use
The product is suitable for repeated use. The number of times it can
be used depends on how often and in which way the product is used.
1. Before reuse, clean the product thoroughly, see section 5.2
Cleaning and care, page 2 .
6.3 Disposal
The disposal and recycling of used devices and packaging must comply
with the applicable local legal regulations.
1. Ensure that the cushion is cleaned prior to disposal to avoid any
risk of contamination.
1579751-A

7 Technical data

7.1 General data
Product
Total height [mm]
Total width [mm]
Total depth [mm]
Maximum user weight
[kg]
Weight complete
cushion [kg] 1)
Weight outer cover [kg] 1)
1) Weights can vary depending on size of cushion ordered.
Size charts and local requirements / certification available upon
request from Invacare®.
7.2 Materials
Foam top High resilient Polyurethane foam
layer
Foam High resilient Polyurethane foam
bottom
layer
Knitted polyamide, coated with an anti-microbial
Cover
polyurethane coating. Substrate treated with a
fluorocarbon to give water/stain resistance.
All cushion components are Latex-free.
7.3 Environmental Parameters
Operating conditions
Ambient temperature
Relative humidity
Atmospheric pressure
Storage and shipping conditions
Ambient temperature
Relative humidity
Atmospheric pressure
1 Allgemein
1.1 Allgemeine Informationen
Diese Gebrauchsanweisung enthält wichtige Informationen zur
Handhabung des Produkts. Lesen Sie die Gebrauchsanweisung
sorgfältig und befolgen Sie die Sicherheitshinweise, damit eine sichere
Verwendung des Produkts gewährleistet ist. Weitere Informationen
erhalten Sie bei der Niederlassung von Invacare® in Ihrem Land
(Anschriften finden Sie auf der Rückseite dieser Gebrauchsanweisung).
1.2 Symbole in dieser Gebrauchsanweisung
Warnungen sind in dieser Gebrauchsanweisung mit Symbolen
gekennzeichnet. Die Warnsymbole sind neben einer Überschrift
abgebildet, die auf die Gefährlichkeit hinweist.
Kidabra-
Matrx® Matrx®
–Vi cush-
Vi Vi heavy
ion
cushion duty
cushion
38 57
300 – 360 360 – 510 460 – 760
300, 360 380 – 510 460 – 660
68 136
0.5 – 0.7 0.9 – 2.0
0.19 0.25 – 0.44
10 - 35 °C
30% - 75% Non-Condensing
70 - 106 kPa
-40 - 70 °C
10% - 100%
50 - 106 kPa
57
272
1.6 – 4.0
0.4 – 1.0
IdeI
3