Description Of Cabling/Modular Contacts; Self-Inspection Of The Installation - Tylo Sense U 7 Elite Notice D'installation Et D'utilisation

Description of cabling/modular contacts

ELITE
Pos 1A.
NTC
Pin 1:
Pin 2: NTC
Pin 3: NTC
Pin 4:
1A
Pos 6A-9A.
4x RS485 6A
Pin 1: A
Pin 2: B
Pin 3: 12 V
Pin 4: GND
Figure 19: Modular contacts, description
ELITE
(Pos 1-4 and 6-9: RJ10, Pos 5: RJ45)
1A. NTC Sensor
2A. Ext switch (optional)
3A. N/A
4A. N/A
5A. N/A
6A. N/A
7A. N/A
8A. N/A
9A. Controls Elite
10. Modular plug (RJ10)
11. Modular contact (RJ10)
Table 3: Connecting components in modular contacts (maximum cable area for RJ10: 0.90 mm/0.20 mm², AWG24)
Connection of
Temp. sensor (10kohm)
External switch with no wire indicator 2 A/B
External switch with wire indication
NOTE! Crimp pliers are needed if changing modular
cabling, e.g. shortening wires.

SELF-INSPECTION OF THE INSTALLATION

To check the installation:
1. Turn power on at the Circuit Breaker Box.
2. Check that the control panel lights up.
3. Start the heater (see User Guide).
4. Check that all three tubular elements start to heat up (go
red).
Pos 2A. Pos 3A. Pos 4A. Pos 5A.
Ext sw Door sw Bim/NTC Addon (option)
Pin 1: Pin 1: Pin 1: Bim
Pin 2: LED Pin 2: LED Pin 2: NTC
Pin 3: SW Pin 3: SW Pin 3: NTC
Pin 4: 12 V Pin 4: 12 V Pin 4: Bim
2A 3A 4A 5A
7A 8A
PURE
(Pos 1-8: RJ10)
1B. NTC Sensor
2B. Ext switch (External switch
optional)
3B. N/A
4B. N/A
5B. N/A
6B. N/A
7B. N/A
8B. Controls Pure
10. Modular plug (RJ10)
11. Modular contact (RJ10)
Pos Pin
1 A/B 2-3
3-4
2 A/B 2-3-4
PURE
Pos 1B.
NTC
Pin 1:
Pin 2: NTC
Pin 3: NTC
Pin 4:
9A
Pin: 1
Comment
Must be NTC model.
Both constant or impulse deactivation works.
12VDC (max. 40mA).
Please keep these instructions!.
In the event of problems, please contact the retailer where you purchased
the equipment.
© This publication many not be reproduced, in part or in whole, without
the written permission of Tylö. Tylö reserves the right to make changes to
materials, construction and design.
Pos 2B. Pos 3B. Pos 4B.
Ext sw Door sw Bim/NTC
Pin 1: Pin 1: Pin 1: Bim
Pin 2: LED Pin 2: LED Pin 2: NTC
Pin 3: SW Pin 3: SW Pin 3: NTC
Pin 4: 12 V Pin 4: 12 V Pin 4: Bim
1B 2B 3B 4B
Pos 5B-8B.
4x RS485
Pin 1: A
Pin 2: B
Pin 3: 12 V
Pin 4: GND
Pin: 4
10
2 3 4
9
5B 6B
8B
7B
3 2 1
11