Commissioning; Maintenance - Toolson WS7200PRO Traduction Des Instructions D'origine

Changing of rolling direction
The installed electrical motor is connected ready to
operate. The connection complies with the relevant
VDE and DIN-regulations. The power supplied by
the customer as well as the used extension cable
should comply with these regulations resp. the
local regulations.
Fig. A

Commissioning

• Before commissioning observe the safety notes.
• All safety and auxiliary installations must be fitted.
• After the complete standstill of the saw, pull the
mains plug or the ignition plug.
• The saw is constructed solely for the cross cutting
of firewood with max. 1 meter length.
• Regardless of the wood diameter, put only one
piece with min. Ø 60 mm on the rocker.
• Functional check before start of work.
• Use both hands to swing the rocker to the saw
blade.
• Then place the rocker in the initial position.
• The wood to be sawn must not be fixed by hand.
• Check the rocker, which must return to the initial
position independently. Check the saw blade for
perfect fit and the correct direction of rotation.
• Only carry out conversion, adjustment, measure-
ment and cleaning work with the engine switched
off. Wait for the rotation of the rotating tool and pull
the spark plug connector.
Sawing
1 Wait until the saw blade has reached full speed.
2 Put the wood on the rocker.
3 Take hold of both handle bars of the rocker with
both hands and lead it evenly to the saw blade;
thus the saw blade is revealed.
4 Push the rocker evenly to ensure the engine
speed does not drop.
5 Remove the wood from the rocker after it has
returned to the initial position and the saw blade
is covered. Then place the next workpiece.
m Attention!
• Do not leave the machine unattended during op-
eration.
• Turn off the machine when not working and pull the
mains plug and spark plug.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
End of work
• Switch off engine at the main switch.
• Wait until the blade has completely stopped.
• Unplug the power cord or the spark plug connec-
tor.
• Observe general maintenance instructions.
• Place the jack in the transport position and secure
it with the locking lever.

Maintenance

m Perform maintenance, modification, adjust-
ment and cleaning work only with the engine
switched off and the mains plug or spark plug
connector is unplugged.
Keep the manual at the machine.
Keep machine clean.
Wear protective goggles when cleaning.
Before undertaking any maintenance or checking
work, the working area must be cleaned. Keep the
necessary tools within the reach of your hand.
The intervals mentioned herein are based on normal
conditions of use. An excessive use of the machine
shortens the intervals accordingly.
Clean the panels, screens and control levers with a
soft cloth. The cloth should be dry or slightly humid
with a neutral cleaning agent. Do not use any sol-
vents like alcohol or benzene as they could damage
the surfaces.
Store oil and grease outside the reach of unauthor-
ized personnel. Strictly follow the instructions on the
bins. Avoid direct contact with the skin. Rinse well
after use.
m Check all safety devices after maintenance
and cleaning work.
Maintenance
Turn the engine off and let the engine cool down.
Remove the spark plug from the spark plug.
Check the general condition of the machine. Be care-
ful with loose screws, misaligned or moving parts,
breakage of parts, and any other condition that could
interfere with safe operation.
Remove any foreign objects and other materials
that have accumulated on the saw blade and the
unit. Clean the machine after each use. Then use a
high-quality and thin fluid machine oil to lubricate all
moving parts.
m Never use a "pressure washer" to clean your
unit. Water can penetrate tight areas of the
machine and its transmission case and cause
damage to spindles, gears, bearings, or the
engine. The use of pressure washers will result
in shortened life and reduce serviceability.
GB 17