Cleaning And Care Of Stainless Steel; Assembly And Commissioning; Set Up Guidelines - Nussbaum SPRINTER MOBIL 2500 Manuel D'exploitation

Additionally, it can also be a pre-requisiste for the
preservation of guarantee claims for any eventual
corrosion damage.
The best protection for the system is regular remo-
val of contaminants of any kind.
This includes above all:
• De-icing salt
• Sand, pebbles, earth
• Industrial dust of all types
• Water, also in connection with other environmen-
tal influences
• Aggressive deposits of all types
• Permanent humidity due to insufficient ventilation
The frequency of system cleaning depends, among
other things on the frequency of use, of system
handling, of workshop cleanliness, and the location
of the system.
Furthermore, the degree of contamination de-
pends on the time of year, the weather conditions
and workshop ventilation.
Under adverse circumstances, weekly system clea-
ning might be required, however a monthly clea-
ning may be sufficient.
Do not use and aggressive and abrasive materials
for cleaning, rather use mild cleaners, e.g. a com-
mercially available detergent and luke warm water.
• For cleaning, do not use high pressure washers
(e.g. steam cleaners).
• Carefully remove all contamination with a
sponge, or if required with a brush.
• Make sure that there is no residue of the cleaner
on the system.
• Dry the system with a cloth and spray it with a
spray wax or oil.
7.4

Cleaning and care of stainless steel

In all cases after assembly, a first cleaning should
be done with our stainless steel cleaner. We recom-
mend our stainless steel cleaning spray (1) for this.
Immediately remove iron particles, grinding dust,
swarf, and weld spatter. These foreign bodies can
accelerate rust if they are deposited on the stainless
steel surface. The passive layer of the non­corroding
steel is broken and this leads to pinhole corrosion.
To guarantee a perfect stainless steel, in princi-
ple we recommend regular cleaning and care
of stainless steel in exterior areas (at best every 6
months).
Contamination and deposits that have already
occurred or severe corrosive etching can be remo-
ved with our special „Pelox" cleaner (2).
For stainless steel products that are placed close to
seawater, seawater resistant products can be im-
plemented in V4A quality.
Detailed information can be found under www.
edelstahl-rostfrei.de.
All stainless steel parts from the Feldmann product
range are made from V2A or V4A with material
68
numbers 1.4301 or 1.4401104. The surface is ground
(mostly 240 grit).
Despite the „rust­free" specification, stainless steel
parts can rust!
Stainless steel stands for a guarantee for long life-
time and elegance. To permanently retain the high
value of the surface, it is indispensable to take care
of and protect the material regularly.
Rust bloom can occur due to environmental influ-
ences or improper treatment.
How does rust bloom occur?
Environment related:
• For higher humidity with salt content close to salt
water.
• In industrial areas with particularly aggressive air
contamination (acid rain).
• By surfaces in contact with de-icing salt spray wa-
ter close to streets.
• By contact with chlorine water (V2A is not suitable
for swimming pools).
Assembly related:
• During processing with tools that are in contact
with normal iron.
• From flying sparks that occur e.g. due to grinding
of the surface.
• When the surface comes into contact with buil-
ding-chemical related foreign materials (calcium,
cement dust, etc.) that deposit on the surface.
• Aggressive cleaning materials.
1. Cleaner spray 7064-PF cleans, cares for and pro-
tects stainless steel parts.
2. Pelox 7065-PE special cleaner for the strongest
contamination, films and corrosion.
3. Cleaner and preservative 50­ESP cleans and pro-
tects (long term protection).
8

Assembly and commissioning

8.1

Set up guidelines

• There is the option to anchor the lift on an existing
concrete floor with a quality of min. C20/25, con-
crete thickness min. 160 mm (normal reinforce-
ment).
• To protect the electrical cable all cable conduits
are to be fitted with cable sleeves or flexible pla-
stic pipes.
• After successful lift installation and before first
commissioning, the operating company must
have the lift grounding conductors inspected on­
site according to IEC regulation (60364­6­61). An
insulation resistance test is also recommended.
• The anchoring of the lift must be carried out by
trained manufacturer personnel or a contract
OPI_SPRINTER MOBIL 2500-3000 - HYMAX PRO 2500-3000_V2.3_DE-EN-FR-ES-IT