Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
.
English
Check the accessories prior to use. The
accessories must be perfectly mounted and
be able to rotate freely. Let the machine run
without any load for at least 1 minute. Do not
use damaged, non-circular or vibrating acces-
sories. Damaged accessories can rupture and
cause injuries.
SANDING
•
While sanding, always make sure to hold
the machine firmly with both hands and
ensure that you are standing firmly on the
ground. It is more secure to control the
machine with two hands.
•
Apply only little pressure when sanding.
Applying too much pressure can result in
uneven sanding.
•
Choose the appropriate grain, depending
on the state of the surface and the mate-
rial. Do not sand down for too long on the
same spot.
•
Use finer sanding paper for the second
round of sanding, until you have reached
the desired level of smoothness.
MAINTENANCE AND CLEANING
•
To reduce the risk of injury, always discon-
nect the main power plug before cleaning
the device.
•
Clean your device with a damp cloth.
•
For stubborn dirt, you can moisten the
cloth with a mild detergent or soft soap.
Other cleaning products often contain
chemicals that can damage the plastic
parts of the device.
•
Make sure that air vents always remain
clean and open.
•
Make sure that no liquids get into the
machine and never immerse the device in
liquid.
•
Repairs, inspections of the machine inte-
rior, adjustments, and the replacement of
carbon brushes should only be performed
by a qualified electrician. Only identical
replacement parts should be used! For
more information, please contact cus-
tomer service.
•
Disconnect the main power plug prior to
performing any maintenance work!
22
7062243_MaxxRoll_Ma_#1506-19.indb 22
•
Always keep the ventilation openings (8)
open and clean. After each use, remove
the dirt and dust with a paintbrush or with
compressed air from the ventilation
openings.
•
Never clean the sander with water or other
liquids.
•
If an increased brush sparking occurs, it is
a sign that the carbon brushes must be
replaced. Have the carbon brushes
replaced by a professional.
TECHNICAL DATA
Voltage: _______________ 230 – 240 V~ 50 Hz
Power: ____________________________ 300 W
Rated speed: _____________ 1600 – 3300 min
Sound pressure level L
: _______ 75.40 dB(A)
pA
Uncertainty K: _____________________ 3 dB(A)
Sound power level L
: __________ 86.40 dB(A)
wA
Uncertainty K: _____________________ 3 dB(A)
Hand-arm vibration
Sanding mode a
: _____ 2.124 m/s
h,DS
Polishing mode a
: _____________ 2.540 m/s
h,P
Wire brushing mode a
h,WB
Uncertainty K: _____________________1.5 m/s
Residual risks
Even when the power tool is used
as prescribed it is not possible to
eliminate all residual risk factors. The
following hazards may arise in connection
with the power tool's construction and
design:
1.
Damage to lungs if an effective dust mask
is not worn.
2.
Damage to hearing if effective hearing
protection is not worn.
3.
Damages to health resulting from vibration
emission if the power tool is being used
over longer period of time or not
adequately managed and properly
maintained.
WARNING! This power tool produces an
electromagnetic field during operation. This
field may under some circumstances interfere
with active or passive medical implants. To
reduce the risk of serious or fatal injury, we
recommend persons with medical implants to
consult their physician and the medical implant
manufacturer before operating this machine.
-1
<2.5 m/s
2
2
2
: _ 2.181m/s
<2.5 m/s
2
2
2
08-09-15 11:05
Publicité
Table des Matières
