Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
•
Insert the weight-mounting sleeve (36) into the select rod (15), and attach both
parts using the quick pin (35). Slide the upper weight plate (14) onto the tubes, and
position the sleeve (36) in such a way that it fits into the bottom of the upper weight
plate (14). Place the washer (39) on the hole in the center of the upper weight
plate (14).
•
Install the four protective covers (54) on the support plate (53) that has been
attached to the base frame earlier. Attach the support plate (53) on top of
the protective cover (54), and secure the whole assembly with the protective
sleeves (55).
Step 2:
33
25
46
24
3d
26
48
46
23
•
Attach the seat tube (20) to the vertical standpipe (2). To do so, use the bolts (1k),
washers (2d) and nuts (3d).
•
Attach the leg extension mount (26) to the seat tube (20) using the bolts (1m),
washers (2d) and nuts (3d).
•
Connect the biceps padding (33) to its support frame (25). To do so, use the
bolts (1c) and washers (2c). For using the biceps padding: Insert the biceps padding
into the leg extension mount (26). To do so, remove the (48) round head grooved pin
first. Reinstall the round head grooved pin after having inserted the padding.
•
Attach the cross braces (23 & 24) and the leg padding (46).
•
Attach the back cushion (28) to the vertical standpipe (2) and the seat cushion (29)
to the seat tube (20). To do so, use the bolts (1a) and washers (2d).
SP-HG-010-IM-DE+GB+FR-02.indb 22-23
1a
2d
28
2
29
2d
2c
1c
1a
3d
2d
20
1k
2d
2d
2d
1a
1m
2d
1a
46
46
22
Step 3:
2f
3f
40
2f 1f 49
1g
2f
8
18
1b
12
2f
2b
3b
3f
2b
32
19
37
47
•
Insert the weight guide tubes (7) into the upper lift arm mount (1). Connect both
parts using the bolts (1d) and washers (2d). Attach the upper lift arm mount (1) to the
vertical standpipe (2). To do so, use the bolts (1k), washers (2d) and nuts (3d). TO
NOT FULLY TIGHTEN AT THIS MOMENT.
•
Attach the chest press (18) to the upper lift arm mount using one bolt (1f),
washers (2f) and one nut (3f).
•
Attach the left (9) and right (8) butterfly braces to the chest press (18). To do so,
use the ball pins (40), screws (1g), washers (2f) and nuts (3f). NOTE: FOR EVERY
BRACE, USE 2 WASHERS, 1 BOLT AND 1 NUT EACH.
•
Slide the arm cushions (19) including PVC pad (37) onto both braces (8 & 9). Then
slide the hand paddings (47) onto the handles that are welded to the braces (8 & 9).
Moisten the insides of the paddings with some soapy water in order to facilitate
installation of the paddings.
•
Attach the handles (12) to the inside or outside of both braces (8 & 9). To do so, use
the bolts (1b), washers (2b) and nuts (3b).
1d
3d 2d
1
2d
2d
1k
1g
2f
1n
6
10
3f
2f
3
1g
2f
2f
3f
2
5
9
2b
1b
2b
12
3b
19
37
47
23
10/6/2016 3:11 PM
2f
Publicité
Chapitres
Table des Matières
