Legal Notice; Explanation Of Symbols; Preparing For Installation - Hauff-Technik MIS 40/2×5-7 Instructions D'installation

MIS 40S
Table of contents
1

Legal notice .........................................................8

2

Explanation of symbols ......................................8

3 Tools and aids required ......................................8
4 Description ..........................................................8
5 Preparing installation .........................................8
6 Assembly .............................................................8
1 Legal notice
Copyright © 2019 by
Hauff-Technik GmbH & Co. KG
Dept.: Technical Editing
Robert-Bosch-Straße 9
89568 Hermaringen, GERMANY
Tel. +49 7322 1333-0
Fax +49 7322 1333-999
E-mail offi ce@hauff-technik.de
Internet www.hauff-technik.de
Reproduction of these installation instructions – even in ex-
tracts – in the form of reprint, photocopy, on electronic data
media or using any other method requires our written consent.
All rights reserved.
Subject to technical alterations at any time and without prior
announcement.
These installation instructions form part of the product.
Printed in the Federal Republic of Germany
2 Explanation of symbols
1
Work stages
►
Effect/result of a work step
1
Reference numerals in drawings
3 Tools and aids required
To install the MIS 40 S/2x5 -7 (MIS 40 S/9-12) for sloping
entry correctly, you will need the following special tools and
auxiliaries in addition to the usual tools:
• Drill, e.g. HILTI DD200 with drill bit (no fi g.) for drill
hole Ø 40–50 mm
• Hauff MIS 40-SVS quick tensioning device, reusable, 1
included in each packing unit (= 10 pcs.)
• Cartridge gun
• M4x70 hexagon socket screw (only for MIS 40S/2x5-7)
• Saw
• Metre rule
• Lubricant (e.g. soapsuds)
• Side cutters
• Screwdriver
A cartridge gun is required for the correct processing
of the expansion resin (Art. No.: 1920002002). This
can be ordered directly through Hauff-Technik (see
fi g.: 1).
12
4
Description: MIS 40 S/9-12 (see fi g.: 3).
Legend for fi g.: 3
1
2
3
4
5
6
7
8
Description: MIS 40S installation situation (see fi g.: 4).
Legend for fi g.: 4
1
2
3
5
1
6
1
Legend for fi g.: 6
1
2
Art. Nr.: 5090032010 Rev.: 00/2019-06-05
The cartridge gun (Art. No.: 1920002002) must be
used to ensure proper processing. You can purchase
this directly via Hauff-Technik (see fi g.: 2).
Description
Membrane opening 9-12 mm
External fl ange
Counter bearing
Resin fi ller tube
Wall entry pipe
Membrane hose
Tubular guide elbow
Wall rosette
Installation depth 200 - 1200 mm
Diameter of drill hole Ø 40 -50 mm
Inside of building

Preparing for installation

A drill hole with Ø 40 - 50 mm is created. This can
be guided manually or using a drill stand (see fi g.:
5).
• It is only possible to drill into solid material.
• If a "wet drilling" technique is used, we
recommend using a water collection system
so that the water can be extracted by suction
directly at the borehole.
• If the drill hole chips over a large area, then
the plaster must be properly restored and
coated according to DIN 18533.
Assembly
Insert MIS into the drill hole from the inside of the
building. Arrange so that the resin injection
hose is at the top (see fi g.: 6).
Inside of building
Resin fi ller tube
► The fl ange must protrude between 30 and 50
mm from the opening on the outside of the
building (see fi g.: 7).
EN