Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 8
The door rollers can now slide into door runner
bar (4084 / 4085) (4.7). Please ensure that the
door gliders are also running on the bottom
track (4.5). Once the door is correctly in place,
connect nuts and bolts into both ends of door
runner bar (4084 / 4085), as door stoppers.
Adjust the door so that it moves freely.
5. ROOF VENT
Connect the side bars (1065) and the top bar
(1064) depending on the glass thickness.
Up to 4 mm, see (5.1). For 4 mm and over,
see (5.2).
Place the bolts to connect the bottom bar
(1066) in the prepared holes, and then slide
the glass into the tracks in side bars (1065)
(5.3).
Now connect bottom bar (1066), and ensure
that the window is totally square before
tighten ing all bolts.
Position the window in the ridge bar from one
end (5.4) and (5.5) and slide it to the required
position (5.6).
Connect the window sill (1063), with the extra
bolt(s) (1001) in the glazing bar(s) (4055) (5.7)
and bolt (2001)* on the corner bar.
*For model 2: It is recommended that the roof
vent be connected in the middle section. In
this case use bolts (1001) already placed in
the glazing bars and bolt (2001) is not required.
Bolt the window opener (1067) to the bottom
bar (1066) using screws (1006) (5.8).
Place the plastic cap (1019) over the end of
the window opener (5.6) and connect both
window fi xers (1016) onto the window sill
(1063) using screws (1006) (5.8).
6. GLAZING – CLEAR/FROSTED
GLASS
Please note the already mentioned safety pre-
cautions.
The door can be positioned in any front
section. Leave the required section free at
this point.
Press the glazing seals (1020) onto the alumi-
nium profi les (6.3) and cut to length.
On the roof begin by positioning the glass at
the ridge and fi x in place using the glazing
spring clips (1011) (6.2). The following pane
should slide under the pane directly above it
with the glass retaining clips (1012) between
the panes (6.1). If diffi culties arise in placing
the last pane, please ensure that those above
have not slipped down.
On the sides please begin from the bottom.
703.01.1103
If you've chosen polycarbonate sheets instead
of glass panes, please use the instructions
included in the carton with the polycarbonate
sheets.
PC. GLAZING – POLYCARBONATE
PANES
Please note the already mentioned safety pre-
cautions.
The door can be positioned in any front
section. Leave the required section free at
this point.
Please check that all listed parts are included.
Important! The UV-resistant side is indicated
by the plastic folio and printing at the edge.
This side must face outside. Remove the folio.
Note! Completely remove the folio only after
the pane has been positioned in the green-
house. (The panes are cut marginally shorter
to allow for expansion in warm conditions.)
Press the glazing seals (1020) onto the
aluminium profi les (PC2) & (PC3) and cut to
length.
Fix the glazing panes in place using the
glazing spring clips (1011) (PC2) and note the
quantity required on each pane.
In order to give the Polycarbonate panes extra
stability, it is recommended to connect them to
the bottom aluminium profi le, in the middle of
each pane, with a screw and washer. To
achieve this it is necessary to drill a 2mm hole
through the pane and the aluminium profi le.
The drill is not included.
The panes on the sides should be connected
with the included H-plastic (24674). (PC1)
FINISHING
If desired, it is possible to seal the greenhouse
at the edges using neutral silicone. Silicone is
not in cluded.
Place the warning label inside the house.
A full range of greenhouse accessories, to help
you make the most of this product, is available
from your stockist. Please inform yourself as to
the possibilities.

SAFETY NOTICE

In the event of high wind conditions, close the
door and all vents.
In the event of heavy snowfall, clear the roof
of the building or take suitable measures to
support the roof. Heat the building in winter.
COMMENTS
For the complete protection of your new
greenhouse, we advise you to include it in
your house insurance. Please take note of
possible building rules relating to the position-
ing of greenhouses.
Please stick the included greenhouse model
label onto the door bar (1062) after success-
fully assembling this product. This information
is important in the event that replacement
parts are later required.
Please keep these Assembly Instructions in
a safe place, for future reference!
Our policy is one of continuous improvement
and we reserve the right to change the specifi -
cations without prior notice.
7

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Smart 2

Table des Matières